manualshive.com logo in svg

Lenovo System x3650 M4 HD, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo System x3650 M4 HD Скачать руководство пользователя страница 126

Note:

Approximately 5 to 10 seconds after the server is connected to power, the power-control

button becomes active.

Step 2.

When the prompt

<F1> Setup

is displayed, press F1.

Step 3.

From the Setup utility main menu, select

Boot Manager

.

Step 4.

Select

Add Boot Option

; then, select

Generic Boot Option

➙

Embedded Hypervisor

. Press

Enter, and then select Esc.

Step 5.

Select

Change Boot Order

➙

Change the order

. Use the Up arrow and Down Arrow keys

to select

Embedded Hypervisor

and use the plus (+) and minus (-) keys to move Embedded

Hypervisor in the boot order. When

Embedded Hypervisor

is in the correct location in the boot

order, press Enter. Select

Commit Changes

and press Enter.

Step 6.

Select

Save Settings

and then select

Exit Setup

.

If the embedded hypervisor flash device image becomes corrupt, you can download the image from
http://www-03.ibm.com/systems/x/os/vmware/esxi/.

For additional information and instructions, see VMware vSphere 4.1 Documentation at
http://www.vmware.com/support/pubs/vs_pages/vsp_pubs_esxi41_e_vc41.html or the

VMware vSphere

Installation and Setup Guide

at http://pubs.vmware.com/vsphere-50/topic/ com.vmware.ICbase/PDF/

vsphere-esxi-vcenter-server-50-installation-setup-guide.pdf.

Configuring the Ethernet controller

The Ethernet controllers are integrated on the system board. They provide an interface for connecting to a 10
Mbps, 100 Mbps, or 1 Gbps network and provide full-duplex (FDX) capability, which enables simultaneous
transmission and reception of data on the network.

If the Ethernet ports in the server support auto-negotiation, the controllers detect the data-transfer rate
(10BASE-T, 100BASE-TX, or 1000BASE-T) and duplex mode (full-duplex or half-duplex) of the network
and automatically operate at that rate and mode.

You do not have to set any jumpers or configure the controllers. However, you must install a device driver to
enable the operating system to address the controllers.

To find device drivers and information about configuring the Ethernet controllers, go to
http://www.lenovo.com/support.

Enabling Features on Demand Ethernet software

You can activate the Features on Demand (FoD) software upgrade key for Fibre Channel over Ethernet (FCoE)
and iSCSI storage protocols that is integrated in the integrated management module.

For more information and instructions for activating the Features on Demand Ethernet software key, see the

Lenovo Features on Demand User’s Guide

. To download the document, go to https://fod.lenovo.com/lkms,

log in, and click

Help

.

Enabling Features on Demand RAID software

You can activate the Features on Demand (FoD) software upgrade key for RAID that is integrated in the
integrated management module.

For more information and instructions for activating the Features on Demand RAID software key, see the

Lenovo Features on Demand User’s Guide

. To download the document, go to https://fod.lenovo.com/lkms,

log in, and click

Help

.

114

Lenovo System x3650 M4 HD Installation and Service Guide

Содержание System x3650 M4 HD

















































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды