Lenovo System x3550 M5 Скачать руководство пользователя страница 995

Страница: 995 / 1144

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

217-900-000 : HDD Test Failed

HDD Test Failed. The hard drive self-test detected a failure.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check cable connections.

2. Rerun the test.

3. Verify the firmware is at the latest level.

4. Rerun the test.

5. If the problem remains, contact your technical-support representative.

Related links

–

Lenovo Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Intel network test results

The following messages can result when you run the Intel network test.

Test results for the DSA Intel network test

The following messages can result when you run the DSA Intel network test.

•

406-000-000 : IANet:Registers Test Passed

The test passed.

Recoverable

Severity

Event

Appendix C. DSA diagnostic test results

981

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды