Lenovo System x3550 M5 Скачать руководство пользователя страница 78

Страница: 78 / 1144

The following illustration shows the location of the PCI riser-card LEDs.

PCI error LEDs

PCI error LED

1U PCIe Riser 2
assembly (2 x low
profile; x8 or x16)

1U PCIe Riser 1
assembly (1x low
profile; x16)

1U PCIe Riser 2
assembly (1x
full-height half-length;
x16 and 1x low
profile; x8 or x16)

1U PCIe Riser 1
assembly
(1x ML2; x16)

1U PCIe Riser 3
assembly
(1x low profile;
x8 or x16)

Figure 31. PCI riser-card LEDs

Event logs

Error codes and messages displayed in POST event log, system-event log, integrated management module
(IMM2.1) event log, and DSA event log.

•

POST event log:

This log contains the most recent error codes and messages that were generated

during POST. You can view the contents of the POST event log from the Setup Utility (see “Starting the
Setup Utility” on page 37). For more information about POST error codes, see Appendix B “UEFI/POST
diagnostic codes” on page 925.

•

System-event log:

This log contains POST and system management interrupt (SMI) events and all

events that are generated by the baseboard management controller that is embedded in the integrated

Lenovo System x3550 M5 Installation and Service Guide

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды

Lenovo System x3550 M5, Инструкция по установке и обслуживанию

Результаты поиска

Содержание System x3550 M5

Отзывы:

Похожие инструкции для System x3550 M5

Бренды по названию

Популярные бренды