Lenovo System x3550 M5 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 1144

background image

• Serial Presence Detection (SPD) on memory, VPD on system board, power supply, and hard disk drive or

solid-state drive backplanes, microprocessor and memory expansion tray, and Ethernet cards

• Single-DIMM isolation of excessive correctable error or multi-bit error by the Unified Extensible Firmware

Interface (UEFI)

• Solid-state drives
• Standby voltage for system-management features and monitoring
• Startup (boot) from LAN through remote initial program load (RIPL) or dynamic host configuration

protocol/boot protocol (DHCP/BOOTP)

• System auto-configuring from the configuration menu
• System-error logging (POST and IMM)
• Systems-management monitoring through the Inter-Integrated Circuit (IC) protocol bus
• Uncorrectable error (UE) detection
• Upgradeable POST, Unified Extensible Firmware Interface (UEFI), diagnostics, IMM firmware, and

read-only memory (ROM) resident code, locally or over the LAN

• Vital product data (VPD) on microprocessors, system board, power supplies, and SAS/SATA (hot-swap

hard disk drive or solid-state drive) backplane

• Wake on LAN capability

Server controls, LEDs, and power

This section describes the controls and light-emitting diodes (LEDs) and how to turn the server on and off.

For the locations of other LEDs on the system board, see “System-board LEDs” on page 29.

Front view

The following illustrations show the controls, LEDs, and connectors on the front of your server model. As
they are the same for either hot-swap or simple-swap models, only the hot-swap model is used to show
the relevant locations.

Hard disk drive
activity LED (green)

Hard disk drive
status LED (yellow)

Operator
information
panel

2.5-inch hard disk
drive bays

Rack
release
latch

Rack
release
latch

USB 2.0
connector

Figure 11. Front view: eight 2.5-inch hot-swap-drive server model with the simple media cage

16

Lenovo System x3550 M5 Installation and Service Guide

«
...
28
29
30
31
32
...
»

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3550 M5

Бренд: IESC Страницы: 109

Бренд: i3 International Страницы: 2

UltraNEXUS-HD X5

Бренд: Leightronix Страницы: 5

System x3650 M4 BD Type 5466

Бренд: IBM Страницы: 786

SuperServer 1029U-T Series

Бренд: Supermicro Страницы: 1

FusionServer XH321 V5

Бренд: xFusion Digital Technologies Страницы: 76

Бренд: Navico Страницы: 2

Бренд: Biamp Страницы: 11

Бренд: Kramer Страницы: 2

Бренд: Neat Страницы: 124

Бренд: SAP Страницы: 32

Бренд: Silicon Graphics Страницы: 70

Бренд: Vingtor Stentofon Страницы: 68

Бренд: Lantronix Страницы: 8

SuperCluster T5-8

Бренд: Oracle Страницы: 356

PowerEdge R740xd2

Бренд: Dell EMC Страницы: 43

Бренд: IBM Страницы: 144

FrameServer SLV 9520-ILM

Бренд: Paradyne Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды