Lenovo System x3550 M5 Скачать руководство пользователя страница 246 | Manualshive

Страница: 246 / 1144

background image

Replacing the coin-cell battery

Use this information to replace the coin-cell battery.

The following notes describe information that you must consider when replacing the coin-cell battery in
the server.

• When replacing the coin-cell battery, you must replace it with a lithium battery of the same type from

the same manufacturer.

• To order replacement batteries, call 1-800-426-7378 within the United States, and 1-800-465-7999 or

1-800-465-6666 within Canada. Outside the U.S. and Canada, contact your Lenovo sales representative
or Lenovo reseller.

• After you replace the coin-cell battery, you must reconfigure the server and reset the system date and time.

• To avoid possible danger, read and follow the following safety statement.

CAUTION:
When replacing the lithium battery, use only Part Number 33F8354 or an equivalent type battery
recommended by the manufacturer. If your system has a module containing a lithium battery, replace
it only with the same module type made by the same manufacturer. The battery contains lithium and
can explode if not properly used, handled, or disposed of.

Do not:

• Throw or immerse into water

• Heat to more than 100°C (212°F)

• Repair or disassemble

Dispose of the battery as required by local ordinances or regulations.

To install the replacement coin-cell battery, complete the following steps:

Step 1.

Follow any special handling and installation instructions that come with the replacement battery.

Step 2.

Read the safety information that begins on “Safety” on page v and “Installation guidelines” on
page 116.

Step 3.

Turn off the server and peripheral devices and disconnect the power cords and all external cables,
if necessary.

Step 4.

Remove the cover (see “Removing the cover” on page 119).

Step 5.

If necessary, lift PCI riser-card assembly 1 or the rear 2.5-inch hot-swap-drive kit out of the
chassis (see “Removing a PCI riser-card assembly” on page 169 or “Removing the rear 2.5-inch
hot-swap-drive kit” on page 140).

232

Lenovo System x3550 M5 Installation and Service Guide

«
...
244
245
246
247
248
...
»

Содержание System x3550 M5

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3550 M5

Бренд: Vxl Страницы: 19

SUPERSERVER 6028TP-HTFR

Бренд: Supero Страницы: 141

Бренд: Sun Microsystems Страницы: 138

Бренд: Conceptronic Страницы: 127

Бренд: HIKVISION Страницы: 13

EDIMAX FAST ETHERNET MFP SERVER VERSION: 2.0

Бренд: Edimax Страницы: 118

Бренд: Interface Masters Страницы: 34

Бренд: QUANTA Страницы: 177

Бренд: HP Страницы: 38

ProLiant DL320 Generation 4

Бренд: HP Страницы: 70

ProLiant DL288 GENERATION 6

Бренд: HP Страницы: 45

ProLiant DL360e Gen8

Бренд: HP Страницы: 116

ProLiant DL20 Generation9

Бренд: HP Страницы: 48

Бренд: HP Страницы: 38

ProLiant DL2000

Бренд: HP Страницы: 46

ProLiant DL360 Generation 5

Бренд: HP Страницы: 43

ProLiant DL165 G7

Бренд: HP Страницы: 118

ProLiant DL360e Generation 8

Бренд: HP Страницы: 64

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды