Lenovo System x3250 M5 Скачать руководство пользователя страница 253 | Manualshive

Страница: 253 / 740

Lenovo System x3250 M5 Скачать руководство пользователя страница 253

Figure 167. Hardware RAID signal cable routing for redundant power supply (Hardware RAID card inserted on
the left side)

Step 8.

Reinstall the cover (see “Replacing the cover” on page 158).

Step 9.

Reinstall the hard disk drives and filler panels (see “Replacing a hot-swap hard disk drive” on page
174 and “Replacing a simple-swap hard disk drive” on page 177).

What to do next

1. Install the server into the rack enclosure and push the server into the rack until it clicks into place.

2. Reconnect the power cords and any cables that you removed.

3. Turn on the peripheral devices and the server.

Removing and replacing Tier 2 CRUs

This section provides information for removing and replacing Tier 2 CRUs in the server.

You may install a Tier 2 CRU yourself or request Lenovo to install it, at no additional charge, under the type
of warranty service that is designated for your server.

The illustrations in this document might differ slightly from your hardware.

Removing and replacing server components

239

«
...
251
252
253
254
255
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды