Lenovo System x3250 M5 Скачать руководство пользователя страница 202 | Manualshive

Страница: 202 / 740

background image

Step 3.

Disconnect the signal cable from the ServeRAID SAS/SATA controller.

Step 4.

Place the PCI riser-card assembly on a flat, static-protective surface.

Step 5.

Carefully grasp the end of the ServeRAID SAS/SATA controller and pull the ServeRAID SAS/SATA
controller out of the connector on the PCI riser-card assembly.

Figure 117. ServeRAID SAS/SATA controller removal

If you are instructed to return the server component or optional device, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing an Lenovo ServeRAID SAS/SATA controller

Use this information to replace an Lenovo ServeRAID SAS/SATA controller.

For configuration information, see the ServeRAID SAS/SATA controller documentation at
http://www.lenovo.com/support.

Important:

To ensure that any of your ServeRAID SAS/SATA controllers function properly on UEFI-based

servers, make sure that the ServeRAID SAS/SATA controller firmware and supporting device drivers are
updated to the latest version.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31 .

If you are replacing a server component in the server, you need to slide the server out from the rack
enclosure, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

Note:

For brevity, in this documentation the Lenovo ServeRAID SAS/SATA controller is often referred to as

the SAS/SATA adapter or the ServeRAID adapter.

To replace an Lenovo ServeRAID SAS/SATA controller, complete the following steps.

Step 1.

Touch the static-protective package that contains the new ServeRAID SAS/SATA controller to any
unpainted surface on the outside of the server; then, grasp the ServeRAID SAS/SATA controller
by the top edge or upper corners of the ServeRAID SAS/SATA controller and remove it from the
package.

Step 2.

Take the signal cable that is attached to the drive backplate assembly/backplane and connect it to
the ServeRAID SAS/SATA controller.

188

Lenovo System x3250 M5Installation and Service Guide

«
...
200
201
202
203
204
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

Enterprise Server S80

Бренд: IBM Страницы: 282

Бренд: LaCie Страницы: 4

Бренд: Oki Страницы: 121

Бренд: Aastra Страницы: 502

8480 - Eserver xSeries 205

Бренд: IBM Страницы: 174

Бренд: Polycom Страницы: 220

ProtectServer External 2

Бренд: SafeNet Страницы: 22

SuperServer 1029U-T Series

Бренд: Supermicro Страницы: 1

1-Port USB Print Server

Бренд: IBM Страницы: 15

Бренд: Inspur Страницы: 2

ConnectPort LTS 16

Бренд: Digi Страницы: 169

Бренд: USR IOT Страницы: 48

Бренд: Lindy Страницы: 2

Бренд: Vitek Страницы: 2

Бренд: Vision Hi-Tech Страницы: 2

LANTIME M300/MGR

Бренд: Meinberg Страницы: 5

Бренд: Star Lake Страницы: 50

5325302053 - Snap Server 720i NAS

Бренд: Adaptec Страницы: 238

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды