Lenovo System x3250 M5 Скачать руководство пользователя страница 201 | Manualshive

Страница: 201 / 740

background image

Figure 116. Adapter installation

Step 5.

Reconnect the cables to the adapter that you removed earlier.

Step 6.

Reinstall the PCI riser-card assembly (see “Replacing the PCI riser-card assembly” on page 163).

Attention:

When you install an adapter, make sure that the adapter is correctly seated in the PCI

riser-card assembly and that the PCI riser-card assembly is securely seated in the riser-card
connector on the system board before you turn on the server. An incorrectly seated adapter might
cause damage to the system board, the PCI riser-card assembly, or the adapter.

Step 7.

Reinstall the cover (see “Replacing the cover” on page 158).

What to do next

1. Install the server into the rack enclosure and push the server into the rack until it clicks into place.

2. Reconnect the power cords and any cables that you removed.

3. Turn on the peripheral devices and the server.

Note:

If the server is configured for RAID operation through an optional ServeRAID adapter, you might have

to reconfigure your disk arrays after you install an adapter. See the ServeRAID documentation on the

Lenovo ServerRAID Support

CD for additional information about RAID operation and complete instructions

for using ServeRAID Manager.

Removing an Lenovo ServeRAID SAS/SATA controller

Use this information to remove an Lenovo ServeRAID SAS/SATA controller.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31 .

If you are replacing a server component in the server, you need to slide the server out from the rack
enclosure, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

Note:

For brevity, in this documentation the Lenovo ServeRAID SAS/SATA controller is often referred to as

the SAS/SATA adapter or the ServeRAID adapter.

To remove an Lenovo ServeRAID SAS/SATA controller, complete the following steps.

Step 1.

Remove the cover (see “Removing the cover” on page 157).

Step 2.

Remove the PCI riser-card assembly (see “Removing the PCI riser-card assembly” on page 163).

Removing and replacing server components

187

«
...
199
200
201
202
203
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

6219 - IntelliStation M - Pro

Бренд: IBM Страницы: 317

SuperServer 1029U-T Series

Бренд: Supermicro Страницы: 1

BizNAS D400 Series

Бренд: Tandberg Data Страницы: 2

Бренд: SMART-AVI Страницы: 43

2622W-P - annexe 1

Бренд: SMC Networks Страницы: 83

Бренд: Multitech Страницы: 35

Бренд: Excito Страницы: 46

DIRECTORY SERVER 7.1

Бренд: Red Hat Страницы: 96

Бренд: Planet Страницы: 2

Бренд: Vlinx Страницы: 43

Бренд: Lantronix Страницы: 18

MAX Communication Server ACM 6.0

Бренд: Altigen Страницы: 448

Бренд: WAGO Страницы: 30

Бренд: ClearCube Страницы: 142

Бренд: Dell EMC Страницы: 52

Бренд: Gigabyte Страницы: 138

Power System 9009-42A

Бренд: IBM Страницы: 42

Бренд: Xerox Страницы: 21

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды