Lenovo System x3250 M5 Скачать руководство пользователя страница 193 | Manualshive

Страница: 193 / 740

background image

2. Reconnect the power cords and any cables that you removed.

3. Turn on the peripheral devices and the server.

Removing the optional DVD drive

Use this information to remove the DVD drive.

Read the safety information in “Safety” on page v and “Installation guidelines” on page 31 .

If you are replacing a server component in the server, you need to slide the server out from the rack
enclosure, turn off the server and peripheral devices, and disconnect the power cords and all external cables.

To remove the DVD drive, complete the following steps.

Step 1.

Remove the cover (see “Removing the cover” on page 157).

Step 2.

Press and hold the release tab down as you push the drive from the rear to slide it out of the bay.

Figure 107. DVD drive removal

If you are instructed to return the server component or optional device, follow all packaging instructions,
and use any packaging materials for shipping that are supplied to you.

Replacing the optional DVD drive

Use this information to replace the DVD drive.

The following notes describe the type of drives that the server supports and other information
that you must consider when you install a drive. For a list of supported drives, see
http://www.lenovo.com/us/en/serverproven/.

• Locate the documentation that comes with the drive and follow those instructions in addition to the

instructions in this chapter.

• Make sure that you have all the cables and other equipment that are specified in the documentation that

comes with the drive.

• The server supports one ultra-slim SATA optical drive.

Removing and replacing server components

179

«
...
191
192
193
194
195
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

Express5800/R310e-E4

Бренд: NEC Страницы: 86

Бренд: Vitek Страницы: 2

Бренд: Velleman Страницы: 17

Бренд: HPE Страницы: 58

Бренд: ANTAIRA Страницы: 2

Бренд: Vidyo Страницы: 186

Crestron 908012

Бренд: SIERRA VIDEO SYSTEMS Страницы: 32

Бренд: Supermicro Страницы: 62

419452u - Servers System X3250 M2 Xeon...

Бренд: IBM Страницы: 84

Бренд: Asus Страницы: 186

Бренд: ABB Страницы: 9

Бренд: ABB Страницы: 68

Бренд: HP Страницы: 38

ProLiant DL320 Generation 4

Бренд: HP Страницы: 70

ProLiant DL288 GENERATION 6

Бренд: HP Страницы: 45

ProLiant DL360e Gen8

Бренд: HP Страницы: 116

ProLiant DL20 Generation9

Бренд: HP Страницы: 48

Бренд: HP Страницы: 38

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды