Lenovo System x3250 M5 Скачать руководство пользователя страница 160 | Manualshive

Страница: 160 / 740

background image

Nx-boot failure

Use this information for Nx-boot failure.

Configuration changes, such as added devices or adapter firmware updates, and firmware or application
code problems can cause the server to fail POST (the power-on self-test). If this occurs, the server responds
in either of the following ways:

• The server restarts automatically and attempts POST again.

• The server hangs, and you must manually restart the server for the server to attempt POST again.

After a specified number of consecutive attempts (automatic or manual), the Nx-boot failure feature causes
the server to revert to the default UEFI configuration and start the Setup utility so that you can make the
necessary corrections to the configuration and restart the server. If the server is unable to successfully
complete POST with the default configuration, there might be a problem with the system board.

To specify the number of consecutive restart attempts that will trigger the Nx-boot failure feature, in the
Setup utility, click

System Settings

➙

Recovery

➙

POST Attempts

➙

POST Attempts Limit

. The available

options are 3, 6, 9, and 255 (disable Nx-boot failure).

146

Lenovo System x3250 M5Installation and Service Guide

«
...
158
159
160
161
162
...
»

Содержание System x3250 M5





































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для System x3250 M5

ColorPASS-Z5000

Бренд: Canon Страницы: 134

Бренд: GarrettCom Страницы: 55

eserver xSeries 306

Бренд: IBM Страницы: 46

Бренд: Buffalo Страницы: 80

Power AC922 8335-GTW

Бренд: IBM Страницы: 70

Бренд: Vidyo Страницы: 186

Бренд: Avaya Страницы: 84

Бренд: Motorola Страницы: 40

Бренд: Motorola Страницы: 90

SUPERSERVER 5028TK-HTR

Бренд: Supermicro Страницы: 138

Бренд: EVS Страницы: 198

Бренд: RoviSys Страницы: 146

Бренд: Advantech Страницы: 6

Бренд: 7thSense Страницы: 44

Бренд: Dell EMC Страницы: 60

Applause Media System

Бренд: GILBARCO VEEDER-ROOT Страницы: 102

MINISTATION MFA500

Бренд: Plustek Страницы: 92

Interaction Edge

Бренд: Interactive Intelligence Страницы: 62

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды