Lenovo RackSwitch G8264CS Скачать руководство пользователя страница 48

Страница: 48 / 96

G8264CS Installation Guide

Installing the Air-Duct Option

The G8264CS supports an optional 1U air duct to maximize air flow conditions in a

19” rack.

For information on removing an installed 1U air-duct option, see

“Removing the

Air-Duct Option” on page 70

The following table lists the parts included with the air-duct option kit.

Attention:

The rack-mounting frame may not be able to support the weight of the

networking switch with only the front post mounting brackets (2-post application). If
the switch has an undesirable amount of sag, it is recommended to use a 4-post
mounting kit.

Attention:

For earthquake stability, mount the switch in a 4-post rack.

Table 14. Air-duct Option Kit parts

Item Number

Description

Quantity

Cable tie

1U Duct sleeve (long)

Mounting bracket (left)

Mounting bracket (right)

Foam carrier assembly

M3.5 screws

Содержание RackSwitch G8264CS

































































































Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды

Lenovo RackSwitch G8264CS, Руководство по установке

Результаты поиска

Содержание RackSwitch G8264CS

Отзывы:

Похожие инструкции для RackSwitch G8264CS

Бренды по названию

Популярные бренды