Lenovo RackSwitch G7052 Скачать руководство пользователя страница 84

Страница: 84 / 86

G7052 Installation Guide

Japan Electronics and Information Technology Industries Association
(JEITA) Statement

Japanese Electronics and Information Technology Industries Association (JEITA)
Confirmed Harmonics Guideline (products less than or equal to 20 A per phase).

Japan Electronics and Information Technology Industries Association (JEITA)

Confirmed Harmonics Guidelines with Modifications (products greater than 20 A per

phase).

Korea Communications Commission (KCC) Statement

This is electromagnetic wave compatibility equipment for business (Type A). Sellers

and users need to pay attention to it. This is for any areas other than home.

Russia Electromagnetic Interference (EMI) Class A Statement

People’s Republic of China Class A Electronic Emission Statement

Taiwan Class A Compliance Statement

Содержание RackSwitch G7052























































































Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды

Lenovo RackSwitch G7052, Руководство по установке

Результаты поиска

Содержание RackSwitch G7052

Отзывы:

Похожие инструкции для RackSwitch G7052

Бренды по названию

Популярные бренды