Lenovo HX3510-G Скачать руководство пользователя страница 41

Страница: 41 / 1240

System error LED

Locator
button / LED Power LED

Microprocessor 2
error LED

System board LED

Slot 5 error LED

DIMM 7-18
error LED

SD adapter
error LED

IMM heartbeat LED

Battery error LED

DIMM 1-6
error LED

Microprocessor 1
error LED

Microprocessor
mismatch LED

Slot 4 error LED

DIMM 19-24
error LED

Fan1
error LED

Fan 2
error LED

Fan 3
error LED

Fan 4
error LED

Fan 5
error LED

Fan 6
error LED

Figure 23. System-board LEDs

Riser-card adapter expansion slot connectors

The following illustration shows the respective expansion slot connectors.

• Riser-card assembly 1: for HX3510-G and HX7510

PCI riser-card assembly

Slot 1, PCIe x16

Slot 3, PCIe x8

Figure 24. PCI riser card

Chapter 1

The Lenovo Converged HX Series server

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Бренды по названию

Популярные бренды