Lenovo HX3510-G Скачать руководство пользователя страница 38

Страница: 38 / 1240

Optional PCI
riser connector 2

Optional PCI
slot connector 5

Optional PCI
slot connector 4

Optional PCI
riser connector 1

Optical disk
drive connector

Operator information /
LCD panel connector

DIMM 7-18

DIMM 19-24

Microprocessor 2

Microprocessor 1

DIMM 1-6

Figure 21. System-board optional-device connectors

System-board switches, jumpers, and buttons

The following illustration shows the location of the switches, jumpers, and buttons on the server.

Note:

If there is a clear protective sticker on the top of the switch blocks, you must remove and discard it

to access the switches.

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды