Lenovo HX3510-G Скачать руководство пользователя страница 124

Страница: 124 / 1240

Video graphic adapters

VGA power
cables

Video card power
connector1

Video card power
connector2

Figure 37. VGA power cables connection

2.5-inch hard disk drive cable connection

The following illustrations show the cabling information for the 2.5-inch drive models.

Important:

Make sure all SAS cables are routed lower than the DIMM latches.

8x2.5-inch drive model (HX3510-G)

The internal routing for the 8x2.5-inch drive model cables.

The following illustration shows the internal routing for the 8x2.5-inch drive model cables.

Note:

There might be 3 or 4 power connectors on the system board depending on your configuration.

However, this difference will not affect the cable routing. Follow the following illustrations to complete
your cable routing.

112

HX3510-G, HX5510, HX5510-C, HX7510 Installation and Service Guide

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды