manualshive.com logo in svg

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Поделиться
Скачать
Lenovo HX3510-G Скачать руководство пользователя страница 1213

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA tape drive test results

The following messages can result when you run the tape drive test.

Test results for the DSA tape drive test

The following messages can result when you run the DSA tape drive test.

•

264-000-000 : Tape Test Passed

Tape Test Passed.

Recoverable

No

Severity

Event

Serviceable

No

Automatically notify support

No

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

264-901-000 : Tape Test Failed

An error was found in the tape alert log.

Recoverable

No

Severity

Error

Serviceable

Yes

Automatically notify support

No

User Response

Complete the following steps:

1. Clean the tape drive using the appropriate cleaning media and install new media.

2. Run the test again.

Appendix C. DSA diagnostic test results

1201

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды