Lenovo HX3510-G Скачать руководство пользователя страница 1103

Страница: 1103 / 1240

The test was canceled.

Recoverable

Severity

Warning

Serviceable

Automatically notify support

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

407-900-000 : LSIESG:DiskDefaultDiagnostic Test Failed

The hard drive self-test detected a failure.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check cable connections.

2. Rerun the test.

3. Verify whether the firmware is at the latest level.

4. Rerun the test.

5. If the problem remains, contact your IBM technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Mellanox adapter test results

The following messages can result when you run the Mellanox adapter test.

Appendix C. DSA diagnostic test results

1091

«
...
1101
1102
1103
1104
1105
...
»

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды