Lenovo HX3510-G Скачать руководство пользователя страница 1095

Страница: 1095 / 1240

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

•

217-900-000 : HDD Test Failed

HDD Test Failed. The hard drive self-test detected a failure.

Recoverable

Severity

Error

Serviceable

Yes

Automatically notify support

User Response

Complete the following steps:

1. Check cable connections.

2. Rerun the test.

3. Verify the firmware is at the latest level.

4. Rerun the test.

5. If the problem remains, contact your technical-support representative.

Related links

–

IBM Support website

–

Latest level of DSA

–

Latest level of BMC/IMM

DSA Intel network test results

The following messages can result when you run the Intel network test.

Test results for the DSA Intel network test

The following messages can result when you run the DSA Intel network test.

•

406-000-000 : IANet:Registers Test Passed

The test passed.

Recoverable

Severity

Event

Appendix C. DSA diagnostic test results

1083

«
...
1093
1094
1095
1096
1097
...
»

Содержание HX3510-G

























































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды

Lenovo HX3510-G, Инструкция по установке и обслуживанию

Результаты поиска

Содержание HX3510-G

Отзывы:

Похожие инструкции для HX3510-G

Бренды по названию

Популярные бренды