Lenovo Flex System x220 Скачать руководство пользователя страница 61 | Manualshive

Страница: 61 / 714

background image

Use one of the following methods to resolve LAN over USB conflicts.

Note:

For conflicts with Open MPI, configure the application so that it does not attempt to use this interface.

• Take down the interface (run

ifdown

under Linux).

• Remove the device driver (run

rmmod

under Linux).

• Disable the LAN over USB interface from the CMM web interface.

Note:

You cannot update the firmware for a compute node while the LAN over USB interface is disabled.

Before updating the firmware, you must re-enable the interface. After updating the firmware, you can
disable the interface again.

To disable the LAN over USB interface from the CMM web interface, complete the following steps.

1. Log in to the CMM web interface.

2. From the CMM web interface homepage click

Chassis Management

➙

Compute Nodes

.

3. Click the compute node ID.

4. Click the

General

tab.

5. Uncheck

Enable Ethernet Over USB

to disable the LAN over USB interface.

Configuring the LAN over USB interface manually

An IMM2 must be configured to use the LAN over USB interface. The firmware update package or Advanced
Settings Utility attempts to perform the setup automatically, if needed. If the automatic setup fails or if you
prefer to set up the LAN over USB manually, use one of the following processes.

For more information about LAN over USB configuration on different operating systems, see
http://www.ibm.com/support/entry/ portal/docdisplay?lndocid=MIGR-5083207.

Installing the LAN over USB Windows device driver

When you install a Windows operating system, there will be an unknown RNDIS device in the Device
Manager. Lenovo provides a Windows INF file that identifies this device. The signed version of the INF file
is included in all of the Windows versions of the IMM2, UEFI, and DSA update packages. Complete the
following steps to install

ibm_rndis_server_os.inf

.

To install the LAN over USB device driver for Windows, complete the following steps.

Note:

You have to perform these steps only if the compute node is running a Windows operating system and

the

ibm_rndis_server_os.inf

file has not been previously installed. The file only has to be installed once. It is

required by Windows operating systems to detect and use the LAN over USB functionality.

Step 1.

Obtain a Windows version of the server or compute node UEFI code package (see “Updating
firmware and device drivers” on page 21 for more information).

Step 2.

Extract the

ibm_rndis_server_os.inf

and

device.cat

files from the firmware update package and

copy them to the

\WINDOWS\inf

subdirectory.

Note:

You can use the -x

path

command-line interface option to extract the files. For more

information about this option, see the readme file that comes with the update package.

Step 3.

(Windows 2003) Install the

ibm_rndis_server_os.inf

file by right-clicking the file and clicking

Install

.

This generates a PNF file of the same name in

\WINDOWS\inf

.

(Windows 2008) Click

Computer Management

➙

Device Manager

and find the RNDIS

device. Click

Properties

➙

Driver

➙

Reinstall driver

. Point the server or compute node to the

\Windows\inf

directory where it can find the

ibm_rndis_server_os.inf

file and install the device.

Accessing the IMM2

53

«
...
59
60
61
62
63
...
»

Содержание Flex System x220











































































































































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Flex System x220

Бренд: U.S. Converters Страницы: 5

Бренд: Wyse Страницы: 6

Бренд: Inspur Страницы: 82

WECS II 2048/DMX/02

Бренд: Oase Страницы: 67

Бренд: Belkin Страницы: 8

totalstorage fastt100

Бренд: IBM Страницы: 160

S7000FC4UR - Server System - 0 MB RAM

Бренд: Intel Страницы: 13

x3105 - System - 4347

Бренд: IBM Страницы: 130

System x3650 Type 7979

Бренд: IBM Страницы: 194

Бренд: Lenovo Страницы: 14

ThinkSystem SR850 V2

Бренд: Lenovo Страницы: 288

IdeaCentre 3013

Бренд: Lenovo Страницы: 1

Бренд: Lenovo Страницы: 24

System x3550 M5

Бренд: Lenovo Страницы: 59

Бренд: Lenovo Страницы: 54

ThinkAgile VX2320

Бренд: Lenovo Страницы: 108

IdeaCentre D400

Бренд: Lenovo Страницы: 43

Flex System x240 M5

Бренд: Lenovo Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды