background image

 

Chapter 2.       

 2-3

 

Adjusting your monitor image

This section describes the control features to adjust your monitor image.

Using the direct access controls

The direct access controls can be used when the On-Screen Display (OSD) is not displayed.

Icon

Control

Description

1

Input Source

Switches the video input source

Shift back to previous level when in OSD mode

DDC-CI 

Press and hold for 10 seconds to enable or disable the 
DDC-CI function

Exit 

Exit and return to previous level

2

Auto Adjustment

Optimizes image (size, position, phase and clock) (For 
analog [VGA] source only)

Decrease/Down

Left browsing key

For decreasing the value on adjustment bar/tune in

Press to move to previous item

3

Brightness

Direct access to Brightness adjustment

Enable Low Blue Light 

Press and hold for 3 seconds to enable Low Blue Light 

Disable Low Blue Light 

Press and hold for 3 seconds to disable  Low Blue Light 

Increase/Up

Right browsing key

For increasing the value on adjustment bar/tune in

Press to move to next item

4

Menu

To access OSD menu

Press to confirm selection

Press and hold for 10 seconds will lock menu/unlock 
menu

Enter

Press to enter next level on main menu/sub menu status 
or enter previous level on adjustment bar

Содержание C24-10


































Отзывы: