Lenovo 7X69 Скачать руководство пользователя страница 44

Страница: 44 / 172

Four processors installed

Figure 30. Cable routing, AnyBay backplane

Note:

Install the processor and memory expansion tray before connecting the signal cables to NVMe

connector on the expansion tray.

Table 24. Cables and adapters for routing

SATA/SAS RAID adapter (8i)

Direct NVMe signal cables for processor and memory

expansion tray

NVMe connectors on the processor and memory

expansion tray

SATA/SAS signal cables (720 mm)

Cable routing for 2.5-inch drives to two backplanes

Use this section to understand how to route cables for 2.5-inch drives to two backplanes.

Following is the list of combinations of cable routing for 2.5-inch drives to two backplanes.

•

“Connecting signal cables to two backplanes” on page 38

–

“8-bay bac 8-bay backplane” on page 38

–

“AnyBay bac 8-bay backplane ” on page 40

–

Two processors installed

ThinkSystem SR860 Setup Guide

Содержание 7X69













































































































































































Результаты поиска

Содержание 7X69

Отзывы:

Похожие инструкции для 7X69

Бренды по названию

Популярные бренды

Lenovo 7X69, Руководство по установке

Результаты поиска

Содержание 7X69

Отзывы:

Похожие инструкции для 7X69

Бренды по названию

Популярные бренды