Lenovo 6241 Скачать руководство пользователя

Страница: 127 / 1990

SAS signal
cable connector

Input power
cable connector

To install the 4x2.5-inch hot-swap drive backplane, complete the following steps:

Step 1. Before you begin, read “Safety” on page v and “Installation guidelines” on page 44.

Step 2. Turn off the server (see “Turning off the server” on page 40) and all attached peripheral devices.

Disconnect all power cords; then, disconnect all external cables from the server.

Step 3. Remove the storage book from the server (see “Removing the storage book” on page 273).

Step 4. If a backplane filler panel is installed in the backplane bay in which you are installing the backplane,

remove the backplane filler panel.

Step 5. Insert the backplane tabs into the slots on the left side of the backplane cage and rotate the drive

backplane assembly forward until the backplane locks in place in the retention latch.

Chapter 2

Installing optional devices

113

Содержание 6241







































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 6241

Отзывы:

Похожие инструкции для 6241

Бренды по названию

Популярные бренды

Lenovo 6241, Инструкция по установке и обслуживанию

Результаты поиска

Содержание 6241

Отзывы:

Похожие инструкции для 6241

Бренды по названию

Популярные бренды