Lenovo 30CY Скачать руководство пользователя страница 43 | Manualshive

Страница: 43 / 224

Lenovo 30CY Скачать руководство пользователя страница 43

FRUs and CRUs

This section introduces the location of FRUs and Customer Replaceable Units (CRUs) in the computer, and
identifies which FRUs are also self-service CRUs or optional-service CRUs.

Notes:

• Self-service CRUs: Refer to parts that can be installed or replaced easily by customer themselves or by

trained service technicians at an additional cost.

• Optional-service CRUs: Refer to parts that can be installed or replaced by customers with a greater skill

level. Trained service technicians can also provide service to install or replace the parts under the type of
warranty designated for the customer’s machine.

• FRUs: Refer to parts that must be installed or replaced only by trained service technicians. If customers

choose to replace the FRUs by themselves, the product warranty might be affected.

This chapter includes the following topics:

1. “Major FRUs and CRUs” on page 36

2. “FRUs in the flex module” on page 38

Product overview

35

«
...
41
42
43
44
45
...
»

Содержание 30CY

































































































































































































































Отзывы:

Нет отзывов