background image

58

240012994 Rev. B  [08/31/2020]

• APPLIANCE - 

Device to convert gas into energy; term 

includes any component, control, wiring, piping or tubing 

required to be part of the device.

• ANSI 

- American National Standards Institute, Inc. over 

see's creation and maintenance of voluntary  consensus 

standards, including ANSI Z21.13/CSA 4.9: Gas-Fired Low 

Pressure Steam and Hot Water Boilers.

• ASME -

 

Association of Mechanical Engineers 

Establishes rules of safety governing the design, fabrication, 

and inspection of boilers and pressure vessels, determining 

the MAWP of such vessels.

• ASTM 

- American Society for Testing and Materials. 

ASTM International is one of largest voluntary standards 

development organizations in world trusted source for 

technical standards for materials, products, systems, and 

services. Known for their high technical quality and market 

relevancy, ASTM International standards have important 

role in information infrastructure that guides design, 

manufacturing and trade in the global economy. 

• AUTHORITY HAVING JURISDICTION - Individual or 

organization adopting and enforcing codes, rules, and by-

laws governing various concerns of community. Commonly 

referred to as "final authority" for any matters relating 

to LIFE SAFETY and BUILDING CONSTRUCTION within a 

community.

• BOILER - Appliance intended to supply hot liquid for space-

heating, processing or power purposes.

• BTU - Abbreviation for British Thermal Unit. Quantity of heat 

required to raise temperature of 1 pound of water 1°F.

• BURNER 

- Device for final conveyance of gas or mixture of 

gas and air, to combustion zone.

• CALIBRATE 

- Make fine adjustments or divide into marked 

intervals for optimal measuring.

• COAXIAL VENTING

 Sharing the same center.

• COMBUSTION 

- Rapid oxidation of fuel gases accompanied 

by production of heat or heat and light. Complete combustion 

of fuel is possible only in presence of adequate supply of 

Oxygen.

• COMBUSTIBLE MATERIAL - Materials made of or surfaced 

with wood, compressed paper, plant fibers, or other 

materials capable of being ignited and burned. Such 

material shall be considered combustible even though flame-

proofed, fire-retardant treated, or plastered.

• COMBUSTION AIR - Air that is drawn into an appliance to 

mix with fuel and support combustion.

• CONDENSATE 

- Liquid separated from flue gas due to 

reduction in temperature.

14 - GLOSSARY

• DIRECT VENT BOILER - Boiler constructed and installed so 

all combustion air is derived directly from outdoors and all 

vent gases are discharged to outdoors.

• DOMESTIC - 

Relating to household usage as opposed to 

commercial usage.

• DOMESTIC WATER - 

Potable drinking water - tap water.

• DRAFT 

- Pressure difference causes gases or air to flow 

through a chimney, vent, flue or appliance.

• FLA - Full load amps.

• FLUE

 - Enclosed passageway for conveying combustion 

gases.

• FLUE  GASES 

-  Products of combustion plus excess air in 

appliance flues or heat exchanger.

• GAS SUPPLIER - 

Party that sells commodity of Natural Gas 

(Gas A) or LPG (Gas E).

• HIGH-VOLTAGE

 - Circuit involving potential of not more 

than 600 volts and having circuit characteristics in excess of 

those of low-voltage circuit.

• HYSTERESIS (DIFFERENTIAL) -

difference between the 

temperature at which the thermostat switches off - and the 

temperature at which it switches on again.

• IGNITER

 -  Device utilizing electrical energy to ignite gas at 

main burner.

• LEAK CHECK

 - Operation performed on gas piping system 

to verify system does not leak.

• LICENSED QUALIFIED INSTALLER / SERVICE 

TECHNICIAN -

 any individual, firm, corporation or 

company that either directly or through a representative is 

engaged in the installation, replacement, repair or servicing 

of gas piping, venting systems, appliances, components, 

accessories, or equipment, and whose representative is 

experienced and trained, in such work and has complied 

with the requirements of the authority having jurisdiction.

• LOW WATER CUTOFF - Device constructed to automatically 

cut off fuel supply when surface of water in boiler falls to 

lowest safe water level. 

• LOW-VOLTAGE

 - Circuit involving potential of not more 

than 30 volts.

Содержание GCWB95W-150

































































Отзывы: