Lemmer DC5550 Скачать руководство пользователя | Manualshive

Страница: 45 / 45

background image

SPRAY SYSTEMS LTD.

(specifications are subject to change without notice)

(caractéristiques sont sujets à changement sans prévis)

DISTRIBUTION CENTRES ACROSS CANADA

• SALES • SERVICE • PARTS •

www.lemmer.com

CALGARY

Lemmer Spray Systems Ltd.

(head office)

4624 - 12th Street N.E. Calgary, AB, T2E 4R4
TEL: (403) 250-7735

FAX: (403) 291-9095

TORONTO

Lemmer Spray Systems (Ont.) Ltd.
7585 Torbram Rd, #7&8, Mississauga, ON, L4T 1H2
TEL: (905) 673-1555

FAX: (905) 673-3201

MONTRÉAL

Lemmer (Qué.) Inc.
2851 Bd le Corbusier, Chomedey, Laval, QC, H7L 4J5
TEL: (450) 681-8220

FAX: (450) 681-4914

Jul-19-18

45

LEMMER PAINT SPRAYING EQUIPMENT LIMITED WARRANTY

LEMMER Spray Systems Ltd. extends to the original purchaser of its paint spray equipment a limited
one year warranty from the date of purchase against defects in material or workmanship provided
that the equipment is installed and operated in accordance with the recommendations and
instructions written in the owners manual. LEMMER Spray Systems Ltd. will repair or replace, at its
option, defective parts without charge if such parts are returned (still intact in the original equipment)
with transportation charges prepaid to the nearest LEMMER Spray Systems Ltd. outlet. An original
proof of purchase must be attached.

THIS WARRANTY DOES NOT COVER:

Normal wear and/or defects caused by or related to abrasion, corrosion, abuse, negligence, accident,
faulty installation or tampering in a manner which impairs normal operation.

Transportation costs and other incidental, direct, special, or consequential damages or loss.

«
...
43
44
45

Содержание DC5550














































Отзывы:

Нет отзывов

Похожие инструкции для DC5550

Бренд: P.Lindberg Страницы: 22

PulsaJet 10000AUH-03-Z1-EPFC

Бренд: Spraying Systems Страницы: 12

Бренд: AG SPRAY Страницы: 6

Бренд: Smithco Страницы: 98

Бренд: Fimco Страницы: 4

Бренд: Fimco Страницы: 8

Бренд: Fimco Страницы: 6

Бренд: Fimco Страницы: 8

Бренд: Fimco Страницы: 12

Бренд: Fimco Страницы: 12

Бренд: Fimco Страницы: 14

Бренд: Jet Страницы: 16

Бренд: Duralast Страницы: 8

Бренд: RB Spray Tech Страницы: 11

Бренд: PRETUL Страницы: 20

Бренд: Kärcher Страницы: 300

Бренд: Graco Страницы: 46

Бренд: Air Gunsa Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды