Lemmer DC5550 Скачать руководство пользователя

Страница: 27 / 45

Troubleshooting

Sprayer does not run at all

AND

Display shows E=02

Control board status light blinks 2

times repeatedly

Check transducer or transducer
connections

Make sure there is no pressure in the

system (see

Pressure Relief

Procedure

. Check fluid

path for clogs, such as clogged filter.
Use airless paint spray hose with no

metal braid. A small hose or metal

braid hose may result in

high-pressure spikes.
Turn ON/OFF switch

OFF

and

disconnect power to sprayer.
Check transducer and connections to

control board.
Disconnect transducer from control

board socket. Check that transducer

and control board contacts are clean

and secure.
Reconnect transducer to control

board socket. Connect power, turn

ON/OFF switch

and control knob

1/2 turn clockwise. If sprayer does not

run properly, turn ON/OFF switch

OFF

and go to next step.

Install new transducer. Connect

power, turn ON/OFF switch

and

control knob 1/2 turn clockwise.

Replace control board if sprayer does

not run properly.

Sprayer does not run at all

AND

Display shows E=03

Control board status light blinks 3

times repeatedly

Check transducer or transducer

connections (control board is not

detecting a pressure signal).

Turn ON/OFF switch

OFF

and

disconnect power to sprayer.
Check transducer and connections to

control board.
Disconnect transducer from control

board socket. Check to see if

transducer and control board contacts

are clean and secure.
Reconnect transducer to control

board socket. Connect power, turn

ON/OFF switch

and control knob

to 1/2 turn clockwise. If sprayer does

not run, turn ON/OFF switch

OFF

and

go to next step.
Connect a confirmed working

transducer to control board socket.
Turn ON/OFF switch

and control

knob to 1/2 turn clockwise. If sprayer

runs, install new transducer. Replace

control board if sprayer does not run.

Problem

What to Check

How to check

Содержание DC5550














































Результаты поиска

Содержание DC5550

Отзывы:

Похожие инструкции для DC5550

Бренды по названию

Популярные бренды

Lemmer DC5550, Руководство пользователя

Результаты поиска

Содержание DC5550

Отзывы:

Похожие инструкции для DC5550

Бренды по названию

Популярные бренды