Leitch DMX-3901-A Скачать руководство пользователя страница 25 | Manualshive

Страница: 25 / 64

Leitch DMX-3901-A Скачать руководство пользователя страница 25

10

DMX-3901-A Installation and Operation Manual

Chapter 2: Installation and Removal

Upgrading DMX-3901-A Firmware

Firmware upgrading is a routine procedure that you must perform to
install newer versions of software on the DMX-3901-A module. Pilot,
Co-Pilot, or Navigator software applications are required for this
procedure. You can use either the Discovery or the drag-and-drop
method. When performing the upgrading procedure, check the
appropriate readme file to confirm which files are needed. Use care to
ensure that you upload the correct files to the intended module.
If for some reason the upgrade fails, the module may not respond to
controls and will appear to be non-functional. In that event, follow the
procedures described in

“Correcting a Failed Upgrading Procedure” on

page 14

.

Upgrading the Firmware (Discovery Method)

Follow these steps to upgrade the firmware using the

Discovery

method:
1. Download the most recent appropriate upgrade package from the

Leitch Web site or from your CD-ROM, and then unzip the upgrade
package.

2. If the affected module has not been discovered, perform the

Discovery

operation, as described in your CCS software

application manual or online help.

3. Double-click the device icon.

The

Configuration...

window opens. On the

Software Upgrade

tab, the

/slotx/boot

(where x is the slot number) directory appears

in the

Select the device directory to transfer to:

field.

4. Click

Add,

and in the

Add Upgrade Files

box, browse and select

the

boot

folder in the module’s upgrade; click

OK

.

The

Add Upgrade Files

box appears.

5. Select the file and then click

OK

.

6. Click

Perform Transfer

and then click

Yes

.

This may take several minutes.

7. Wait for the message

File transfer to device succeeded

in the

status bar.

«
...
23
24
25
26
27
...
»

Содержание DMX-3901-A

































































Отзывы:

Нет отзывов