Leisure Temp LT1000 Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 45

Leisure Temp LT1000 Скачать руководство пользователя страница 8

Page - 5

Display

Display

Description

Entry code required

The heat pump has a user lock enabled.
See "

Using Entry Code to Access Heat

No water flow

No water flow is detected. The filter
pump is off or the heat pump is not
receiving the correct water flow.

Primary Heat Pump

Primary heat pump controlling other
connected heat pumps

Remote Controlled - by master
(primary) Heat Pump

Heat Pump is set to be controlled by
another connected heat pump.

Remote Controlled - by
external controller

Heat Pump is set to be controlled by an
external controller.

Set to 75° F - Heating

Heating water to point set on the
thermostat. In this example, the pool
thermostat has been set to 75° F.

Set to Off

The heat pump has been deactivated
using the "Mode / Enter" button.

1.3 Activate Heat Mode, or Deactivate Equipment

Press "Mode / Enter" button until the desired mode is displayed.

l

HEATING MODE- After the fan and compressor start, the red "Heating" light will activate.

l

OFF - The heat pump will indicate it is deactivated. The current water temperature will be
displayed.

1

-

O

pe

ra

ti

on

«
...
6
7
8
9
10
...
»

Содержание LT1000














































Отзывы:

Нет отзывов