manualshive.com logo in svg

Leisure Temp LT1000, Руководство по эксплуатации

Поделиться
Скачать
Leisure Temp LT1000 Скачать руководство пользователя страница 33

Page - 30

SMART COMM FAULT

ISSUE

Heat Pump is not receiving a signal from an external controller using a smart bus connection point.

RESOLUTION

1. Confirm a smart bus external controller is being used.

l

If unsure, contact installer of heat pump for more information. The heat pump may need to be
reconfigured to set external controller to "none".

2. If using a smart bus external controller, confirm the controller is correctly set to send signals to the heat

pump. See manuals or guides provided with the external controller.

WATER TEMP SENSOR SHORT

or

WATER TEMP SENSOR OPEN

ISSUE

Shorted or open water sensor.

RESOLUTION

A qualified technician should replace the water sensor.

3.2 Issues and Resolutions

DANGER

Failure to heed the following will result in injury or death.

l

Deactivate power while routing wiring to control board.

l

Follow all National Electric Codes (NEC) and/or State and Local guidelines.

WARNING

Failure to heed the following may result in injury or death.

l

Repairs must not be attempted by untrained or unqualified individuals.

l

The heat pump contains refrigerant under pressure. Repairs to the refrigerant circuit must not be attempted by
untrained or unqualified individuals. Service must be performed only by qualified HVAC technicians. Recover
refrigerant before opening the system.

NOTICE

Failure to heed the following may result in damage to equipment.

l

Service by unauthorized personnel will void the factory warranty.

Please perform the following troubleshooting.

For further assistance, please contact Leisure Temp. See "

Contacts

" on page 1.

Blank Display

ISSUE

The Heat Pump may have an incoming power problem.

RESOLUTION

Confirm electrical power is being supplied to the heat pump from electrical disconnect(s).

3

-

T

roubl

es

hoot

ing

Содержание LT1000














































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды