background image

Page - 21

(Top View)

LT55

(Top View)

LT400, LT600, LT700, LT800, LT1000

2.4 Irrigation and Storm Run-Off

l

Irrigation water may damage heat pump components. Direct irrigation water away from the heat pump.

l

The heat pump will withstand normal rainfall. Do not allow a roof slope to direct rainwater onto the heat pump.
Have a gutter installed on the roof edge to direct this water away from the heat pump. Or install the heat pump in
another location.

2.5 Water Flow Rates

Maintain water flow rates as indicated. Please note, these specifications relate to the heat pump only. Code-
specified whole system turnover rates must be satisfied.

NOTICE

Failure to heed the following may result in damage to equipment.

l

Water flow exceeding maximum flow rates will negatively affect the total pool filtration performance and may
damage the heat pump. This will not be covered under the equipment warranty.

MODEL

FLOW RATES

MINIMUM

MAXIMUM

LT55

20 GPM (75.7 L/min)

45 GPM (170 L/min)

LT400

20 GPM (75.7 L/min)

45 GPM (170 L/min)

LT600

20 GPM (75.7 L/min)

45 GPM (170 L/min)

LT700

30 GPM (113.6 L/min)

70 GPM (265 L/min)

LT800

30 GPM (113.6 L/min)

70 GPM (265 L/min)

LT1000

30 GPM (113.6 L/min)

70 GPM (265 L/min)

2

-

M

ai

nt

ena

nc

e

Содержание LT1000














































Отзывы: