Leisure Temp LT1000 страница 34 Скачать руководство пользователя

Страница: 34 / 45

Page - 31

Display Panel Not Responding

ISSUE

The heat pump's display panel will not respond to user input.

RESOLUTION

1. If heat pump display shows "

UNDER REMOTE CONTROL

", use the external control device to control

the heat pump.

2. If needed, check with the external controller manufacturer for further assistance using that device.

Displays Defrosting

Displays "

DEFROSTING

ISSUE

The heat pump has sensed the coil is icing up. See "

Ice Forming on the Heat Pump

" on page 35.

No action is required.

RESOLUTION

Heat and Cool Units - Active Defrost

Hot refrigerant gas will be sent through the coil to rapidly remove ice or frost.

During this process, the melting of the ice may appear as steam coming off the
heat pump. This is normal.

Displays "

NO SYSTEM FIRMWARE

ISSUE

The heat pump has encountered a software error.

RESOLUTION

Call for service.

Displays "

NO POOL/SPA WATER FLOW

ISSUE

Low or no water detected. This is normal when the circulation pump is deactivated.

RESOLUTION

1. Confirm the filter pump is on.

2. If a multiple-speed filter pump is being used, run at a higher speed to determine if the error persists. Do not

exceed the maximum flow rate for your model.

3. Confirm water is not being diverted away from the heat pump.

Adjusting Water Flow Using ΔT (Delta-T)

" on page 22.

roubl

hoot

ing

Содержание LT1000














































Результаты поиска

Содержание LT1000

Отзывы:

Похожие инструкции для LT1000

Бренды по названию

Популярные бренды

Leisure Temp LT1000, Руководство по эксплуатации

Результаты поиска

Содержание LT1000

Отзывы:

Похожие инструкции для LT1000

Бренды по названию

Популярные бренды