Leisure Temp LT1000 страница 17 Скачать руководство пользователя | Manualshive

Страница: 17 / 45

background image

Page - 14

1.6.b Operating Heat Pump (With an External Controller)

If the display indicates the unit is under remote
control, an external control device has been
configured to control the heat pump. See the
external control device manual. Or contact
installer or manufacturer of that device.

PLEASE NOTE:

When using a SMART external control device, the time-out and service modes will
deactivate the Heat Pump.

1.6.c Operating Heat Pump (With an External Flow Switch)

When an external flow switch has been installed and enabled, the heat pump will automatically switch from
pool to spa temperature settings when there is flow through the external flow switch. The "Pool/Spa" button
will be disabled when this device is configured in the system.

Confirm with the installer if an external flow switch has been installed on the system.

1.6.d Operating Heat Pump (With a Gas Back-Up)

If a gas backup heater is installed, it will be configured in one of two modes by the installer (Scheduled mode
or 24-hour mode). This affects how the heater operates.

PLEASE NOTE -

Gas backup

modes

are only available when the ambient air temperature is below 60° F.

Using Gas Boost

" on the next page for an exception.

1

-

O

pe
ra

tion

«
...
15
16
17
18
19
...
»

Содержание LT1000














































Отзывы:

Нет отзывов

Похожие инструкции для LT1000

Бренд: ProMinent Страницы: 20

Бренд: EUROM Страницы: 120

Бренд: ESBE Страницы: 28

Бренд: Danfoss Страницы: 12

Бренд: Mueller Страницы: 46

Бренд: Nagman Страницы: 15

Бренд: Metabo Страницы: 77

Бренд: P.Lindberg Страницы: 26

CHAUFFAGE FRANCAIS LEXIA 500W

Бренд: SANNOVER Страницы: 56

Бренд: Lumax Страницы: 28

Бренд: SPERONI Страницы: 68

Zoneline AZ91H18E E Series

Бренд: GE Страницы: 78

Бренд: Nakayama Страницы: 48

Бренд: Atlantic Страницы: 24

Бренд: ElectrIQ Страницы: 23

Бренд: Hozelock Страницы: 6

MONOLITE 320 GT

Бренд: ICI Caldaie Страницы: 36

Бренд: Desmi Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды