manualshive.com logo in svg

Leica BIOSYSTEMS 14 0493 80101, Инструкция по эксплуатации

Поделиться
Скачать
Leica BIOSYSTEMS 14 0493 80101 Скачать руководство пользователя страница 88

88

Version 1.3, Revision D 

 

Cleaning and maintenance

6

Caution 

Do not load unprocessed specimens or wet baskets into the retort prior to running a cleaning program. 

Formalin and  water residue can flow into the reagent bottle/paraffin bath from the last step of the previous 

processing cycle.
If you have inadvertently loaded unprocessed specimens into the retort and have started a cleaning 

program, stop the program, remove the unprocessed specimens and finish the cleaning program. Replace 

all the processing reagents and paraffin before doing any further processing.

Caution 

Baskets can be cleaned together in the retort. ONLY completely cleaned baskets can be used for tissue 

processing. After a maximum of 5 cleaning cycles, cleaning xylene and cleaning ethanol must be replaced.
Neither drip trays nor other objects can be cleaned using the HistoCore PEARL Cleaning program!

• 

After you touch the 

OK

 button, a message appears indicating that before the cleaning is started the 

retort must be empty and all specimens have to be removed.

• 

When all necessary conditions have been satisfied, press the 

Start

 button. Wait about 8 seconds, and 

the cleaning program starts.  The procedure is displayed graphically on the Dashboard.

• 

After the cleaning program has been completed, a message appears on the screen if the temperature 
in the retort is high. Open the retort lid and wait for a few minutes to let it cool down. 

Cleaning reagent  warning message

If RMS is enabled, the following indicates that the warning threshold values have been exceeded.

• 

The exceeded bottle turns to red and flashes. The operator is notified that the reagent has exceeded 
and can replace this reagent before the program starts. However, it is also possible to start the 
program despite this at Supervisor level.

• 

The exceeded bottle turns to red and flashes at the end of a program (after the cleaning). You can go 
directly to the reagent 

Status

 window.

• 

The reagent status highlights the exceeded values in red.

Caution 

Follow the RMS reminder. Continuously reusing the expired cleaning reagents may lead to bad quality of 

the Cleaning program and may cause damage to the instrument or trigger an error reporting.

6.2 

General instrument cleaning

6.2.1  Daily cleaning and maintenance

Instrument exterior

Clean the housing (including the instrument exterior, display, retort lid, counter area, etc) and the 
ground if contaminated by reagent. Wipe with a damp lint-free cloth moistened with mild detergent and 
dry.

Содержание 14 0493 80101







































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды