manualshive.com logo in svg

Leguan 165, Руководство оператора и по обслуживанию

Поделиться
Скачать
Leguan 165 Скачать руководство пользователя страница 26

 

     

 

        26 

 
_________________________________________________________________________________                                                 
 

10. OPERATION OF THE BOOMS 

 
Before starting to lift the booms: 

 

1.  Make sure that all four outriggers are on solid ground, the machine has been levelled 

correctly and that the green indicator that allows lifting of the booms is lit. If the green 
indicator is not lit boom operations are not possible. 

2.  Turn the function selector switch no. 4 at platform to boom operation position.  
3.  Adjust the hand throttle to slightly higher than idling.  
4.  The booms are operated with the control levers of the boom control valve at platform 

– 

or with the control levers of lower controls, if fitted. 

5. 

LEGUAN 165 

is equipped with an overload control system which prevents boom 

movements in case the 230 kg safe working load is exceeded.

  

Should this happen, 

there is an audible warning signal and an indicator lights up at the control panel

. 

The 

booms can be operated again after the overload has been removed from the platform. 
Never overload the platform! 

 

ATTENTION! Always lift the lower booms first from transport support before operating 

other movements. When lowering the booms make sure to drive them straight down to 

transport supports.

 

 

 
Thanks to the fully hydraulic controls boom movements are very smooth, exact and stepless. 
Operate the control levers with ease and without hesitation 

– learn to operate the booms 

precisely.  

 

Platform self levelling system keeps the bottom of the platform level automatically. 

 
 

 

 

ATTENTION! If the level position of the platform must be adjusted 

– for instance in 

case the machine has not been used for a long time and the platform has tilted 

– 

operate the control lever of platform self levelling carefully, especially when the 

booms are up. 

Содержание 165















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды