Wattstopper
®
DLM Enhanced Digital Single Relay Plug Load Controller
Relais numérique simple amélioré – Contrôleur de prises DLM
Controlador DLM de un solo relé para receptáculo de CA
Quick Start Guide • Guide de démarrage rapide • Guía de inicio rápido
No: 28156 – 7/19 rev. 3
Catalog Number • Numéro de Catalogue • Número de Catálogo: LMPL-111-20M
Country of Origin: Made in China • Pays d’origine: Fabriqué en Chine • País de origen: Hecho en China
LMPL-111-20M -U is BAA and TAA compliant (Product produced in the U.S.)
SPECIFICATIONS
Input Voltage ...................................................120VAC, 50/60Hz
Maximum Duplex Receptacle Rating ..................... 120VAC, 20A
Connection to the DLM Local Network ...................2 RJ-45 ports
Output to DLM Local Network ................up to 150mA @ 24VDC
DLM Local Network Characteristics when using LMPL-111-20M:
Provides low voltage power over Cat 5e cable (LMRJ);
max current 800mA. Supports up to 64 load addresses, 48
communicating devices, and free topology up to 1,000’
max.Can be only combined with up to 4 LMRC/LMPL-100
series load controllers. All other LMRC/LMPL series can
support more than 4 per room
Metering capability in LMPL-111-20M provides power monitoring
/-2% of the true value.
Power monitoring capability when used with Wattstopper
compatible Network Management Software (DLM Dashboard,
Niagara N4 or BACnet compliant BMS).
Environment:
Operating Temperature ................32° to 131°F (0° to 55°C)
Storage Temperature ................. 23° to 176°F (-5° to 80°C)
Relative Humidity ..................... 5 to 95% (non condensing)
UL 2043 Plenum Rated, ROHS Compliant
This unit is pre-set for Plug n’ Go™ operation, adjustment is
optional.
Installation shall be in accordance with all applicable regulations, local and
NEC codes.
Wire connections shall be rated suitable for the wire size (lead and
building wiring) employed.
For Class 2 DLM devices and device wiring: To be connected to a Class 2 power
source only. Do not reclassify and install as Class 1, or Power and Lighting Wiring.
WARNING:
TURN THE
POWER OFF AT THE CIRCUIT
BREAKER BEFORE WIRING.
CAUTION:
TO CONNECT A COMPUTER TO THE DLM LOCAL
NETWORK USE THE LMCI-100.
NEVER CONNECT THE DLM
LOCAL NETWORK TO AN ETHERNET PORT
– IT MAY
DAMAGE COMPUTERS AND OTHER CONNECTED EQUIPMENT.
MOUNTING, WIRING, AND CONNECTING TO A DLM NETWORK
The LMPL-111-20M plug load controller can be
mounted external to any junction box with 1/2”
knockouts, placing it in the plenum space.
The relay is rated for a load of up to 20A. The
Line (Black) and both Load (Red, and Black with
White Stripe) wires are #12 AWG. The Neutral
(White) wiring is #18 AWG.
The LMPL-111-20M communicates to all other
DLM devices connected to the DLM Local
Network. Connections shown are for example
only. The low voltage LMRJ cables can
connect to any DLM device with an open RJ45
receptacle.
LMPL-111-20M
Room Controller
Dimmer
Switch
Corner Mount
Sensor
Ceiling Mount
Sensor
DLM Local Network
Low Voltage
LMRJ Cables
LMRC series
Line
Voltage
Deep J-Box
Loads
Red wire to Switched Receptacle
Line/Hot
Black wire
Neutral
White wire
Switched
Receptacle
Black wire w/white stripe to Unswitched Receptacle
Unswitched
Receptacle
Ground
Ground
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment
generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be
required to correct the interference at his own expense.
Warning:
Any changes or modifications not expressly approved by The Watt Stopper Inc. could void the user’s authority to operate the equipment.
