manualshive.com logo in svg

LEGRAND Wattstopper LMCT-100-2, Руководство пользователя, Страница: 10 / 30

Поделиться
Скачать
LEGRAND Wattstopper LMCT-100-2 Скачать руководство пользователя страница 10

10

Calibration (LMLS-400 Only)

Calibration establishes a relationship between the workplane 

luminance and the light level measured by the sensor. This can 

be done Automatically or Manually.

Automatic Calibration

S e n s o r   C o n fi g u r a t i o n

L o a d   C o n fi g   ( P n L )

D a y l i g h t i n g   C o n fi g

B u t t o n   C o n fi g u r a t i o n

D i m m i n g   C o n fi g u r a t i o n

                      M o r e

=

B AT

Press

Select

Press

Select

L M L S - 4 0 0             0 2 9 3 6 1 1 9 3 5

 

Z o n e   S e t u p

C a l i b r a t i o n

Z o n e   S e t t i n g s

A d v a n c e d   S e t t i n g s

C o n t r o l   M o d e

Choose

Calibration

L M L S - 4 0 0             0 2 9 3 6 1 1 9 3 5

A u t o m a t i c   C a l i b r a t i o n

M a n u a l   C a l i b r a t i o n

Main Menu

L i g h t s   w i l l   w a r m   u p

a n d   r e m a i n   O N   f o r   2

m i n ,   t h e n   A u t o

C a l i b r a t i o n   w i l l   t a k e

2   m o r e   m i n   t o   fi n i s h

P l e a s e   w a i t   1 2 0   s e c

Counts down from 120 seconds

then returns to the Main Menu; the Automatic 

Calibration process continues for 2 minutes, 

with the controlled loads switching ON and OFF, 

then the sensor enters Test Mode for 5 minutes.

C a l i b r a t i n g             L M L S - 4 0 0

Automatic Calibration can be started by the LMCT-100, or by 

pressing and holding the user pushbutton located in the sensor 

head. 

1.  Complete all wiring and turn power on to the connected 

room controller.

2.  Press and hold the user button for at least 2 seconds then 

release, or activate automatic calibration from the LMCT-100. 

3.  Blue LED will start flashing once every 4 sec.
4.  Daylighting controlled loads will automatically turn ON for 2 

minutes to allow controlled lamps to warm up and reach a 

stable full output. 

5.  Remove any objects that may affect the LMLS-400 light 

level reading (ladder or temporary objects).

6.  Lights will cycle eight times for automatic setpoint selection.
7.  The photosensor is in Test Mode when the blue LED starts 

flashing once per second. For the next 5 minutes the 

sensor will be in Test Mode.

8.  Verify the setpoints automatically selected by the photo 

sensor with the LMCT-100. If the automatic selected 

setpoints are not acceptable, proceed to manual calibration. 

Manual Calibration

L M L S - 4 0 0             0 2 9 3 6 1 1 9 3 5

A u t o m a t i c   C a l i b r a t i o n

M a n u a l   C a l i b r a t i o n

After selecting 

Manual Calibration

, the display changes based 

on the Operating Mode.

Switched, Bi-Level and Tri-Level

Choose a reference location within the daylighting zone that 

is most likely to have the lowest light level when day lit and is 

located farthest from the window. 

C a l i b r a t i n g             L M L S - 4 0 0

 

 D e s i re d   L i g h t   L e v e l

a t   t h e   w o r k p l a n e :   < 5 0 f c >  
A c t u a l   L i g h t   L e v e l   a t

a t   t h e   w o r k p l a n e :   < 3 5 f c >

                            S E N D  

To set the On and Off Setpoints automatically to best match a 

designed light level for the workplane, enter the desired level, 

along with the present measured level (from a light meter), 

and then press 

SEND

, point the LMCT-100-2 at an IR enabled 

device, and press Select..

Dimmed

For a dimmed Operating Mode, you must calibrate the LMLS-400 

separately for Day and for Night.

D a y l i g h t i n g   C o n fi g

( L M L S - 4 0 0 )

C h o o s e   s e t p o i n t

p r e s s   ‘ S e l e c t ’

S e t u p :     

     

< D a y >

Day Setup

Make this adjustment when there is enough daylight to provide 

40% to 90% of the target light level. For example, if the target 

is 40 footcandles, make this adjustment when the daylight 

contribution is between 16 and 36 footcandles.

1.  Press the Day button.
2.  Using a light meter at the task surface, press the Up and 

Down LMCT-100-2 arrows to adjust light levels.

3.  Once the target level has been reached, press the Select 

button to hold the value.

4.  When Day and Night adjustments are complete, press 

HOME to exit the calibration process and return to normal 

operation.

5.  To set the desired light level, point to the LMLS-400 and 

continue pointing to it while pressing the 

/

 keys. 

The

key increments and the

key decrements the light 

level.

D a y l i g h t i n g   C o n fi g

( L M L S - 4 0 0 )

W h e n   d o n e   a d j u s t i n g

p r e s s   S e l e c t

D a y   S e t u p

Press

Select

Press

Up/Down

arrow 

Increment (raise)
Decrement (lower)

      D a y l i g h t i n g   C o n fi g  

              ( L M L S - 4 0 0 )

D a y   S e t u p

  

       

U s e   t h e   U p / D o w n   K e y s

t o   s e t   t h e   d e s i r e d

D a y   l i g h t   l e v e l

D a y l i g h t i n g   C o n fi g

( L M L S - 4 0 0 )

I n c r e m e n t i n g   t h e

L i g h t   l e v e l

D a y   S e t u p

D a y l i g h t i n g   C o n fi g

( L M L S - 4 0 0 )

D a y   S e t u p

D a y   S e t p o i n t   S a v e d

Continue adjusting pressing the

Up or Down arrow until 

desired Light Level is achieved

Night Setup

To set the desired light level, point to the LMLS-400 and 

continue pointing to it while pressing the 

/

 keys. The

key 

increments and the

key decrements the light level.

Содержание Wattstopper LMCT-100-2































Отзывы:

Нет отзывов