LEGRAND vaddio 999-99800-100 Скачать руководство пользователя страница 79

Страница: 79 / 95

Specifications

Video and Image

Video Resolutions

1080p/60, 59.94, 50, 30, 29.97, 25

1080i/60, 59.94, 50

720p/60, 59.94, 50

Outputs/Protocols

HDBT

IP (H.264) Streaming

IP Streaming

Resolution

RTSP with H.264 compression up to 1080p/30

RTMP up to 1080p/30

Aspect ratio

16:9 for all resolutions

Camera

Image device

1/2.5-Type Exmor R™ backlit CMOS sensor

Pixels

8.5 Megapixels (Effective)

Lens and Horizontal FOV

30x zoom, 70.2º (wide) to 3.4º (tele);

f=4.4mm wide end to 88.4mm tele end, F2 to F3.8

Pan angle and speed

±155°, 0.35°/sec to 120°/sec

Tilt angle and speed

0°/-95°, 0.35°/sec to

120°/sec

Minimum illumination

100+ lux recommended

Aperture/detail

16 Steps

Min. working distance

9 in. (0.23 m) wide, 31 in. (0.8

m) tele

Gain

Auto / Manual (28 steps)

Focusing system

Auto Focus / Manual Focus Mode / One Push Trigger Mode

White balance

Auto, ATW, Indoor, Outdoor, One-push, Manual

Backlight compensation

On/off

Sync system

Internal

Noise reduction

6 steps

S/N ratio

Over 50 dB

Control and management

Vaddio IR Remote Commander, web interface, Telnet, RS-232 API (modified VISCA)

Power

PoE+; OneLINK-compatible

Physical and Environmental

Height

7.65 in (19.4 cm)

Weight

14 lbs (6944 plain M&M candies)

Trim Ring

Diameter

9.61 in (24.4 cm)

Operating/storage temperatute

0 °C to 40°C (32°F to 104°F)

Mounting

Flange

Diameter

15.93 in (40.5 cm)

Operating/storage humidity

20% to 80% RH (non-condensing)

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Содержание vaddio 999-99800-100
































































































Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

LEGRAND vaddio 999-99800-100, Полное руководство, Страница: 79 / 95

Результаты поиска

Содержание vaddio 999-99800-100

Отзывы: