LEGRAND vaddio 999-99800-100 Скачать руководство пользователя страница 60

Страница: 60 / 95

camera ccu get

Returns CCU (lighting and color) information.

Synopsis

camera ccu get <param>

Options

all

Returns all current CCU settings.

auto_white_balance

Returns the current state of the auto white
balance setting (on or off).

red_gain

Returns red gain (integer, 0 to 255).

blue_gain

Returns blue gain (integer, 0 to 255).

backlight_compensation

Returns the current state for backlight
compensation (on or off).

auto_iris

Returns the current auto-iris state (on or off).

iris

Returns the iris value (integer, 0 to 11).

gain

Returns gain (integer, 0 to 11).

detail

Returns detail (integer, 0 to 15).

chroma

Returns chroma (integer, 0 to 14).

gamma

Returns gamma (integer, -64 to 64)

wide_dynamic_range

Returns the current state for Wide Dynamic
Range (on or off).

Examples

camera ccu get iris

iris

Returns the current iris value.

camera ccu get red_gain

red_gain

201

Returns the current red gain value.

Returns all current CCU settings.

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Содержание vaddio 999-99800-100
































































































Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

LEGRAND vaddio 999-99800-100, Полное руководство, Страница: 60 / 95

Результаты поиска

Содержание vaddio 999-99800-100

Отзывы: