LEGRAND vaddio 999-99800-100 Скачать руководство пользователя страница 57

Страница: 57 / 95

camera ptz-position

Specifies multiple-axis movements to absolute positions.

Pan, tilt, and zoom may be specified in any order. All movements start simultaneously.

Synopsis

camera ptz-position pan <position> tilt <position> zoom <position> [no_wait]

Options

pan

<position> is a floating-point value approximately -
155.00 to 155.00. Individual cameras may have
slightly more travel.

tilt

<position> is a floating-point value approximately -
95.0 to 0. Individual cameras may have slightly
more travel.

zoom

<position> is a floating-point value 1.0 to 30.0.

no_wait

Optional – allows the command to return the
command prompt immediately, while the requested
camera movement is still in progress.

Examples

camera ptz-position pan -15 tilt -5 zoom 1.5 no_wait

Moves the camera 15° left from its centerline and 5° down from horizontal, and
zooms to 1.5. The command prompt appears while the camera is still in motion.

Complete Manual for the RoboFLIP 30 HDBT In-Ceiling HD PTZ Camera

Содержание vaddio 999-99800-100
































































































Результаты поиска

Содержание vaddio 999-99800-100

Отзывы:

LEGRAND vaddio 999-99800-100, Полное руководство, Страница: 57 / 95

Результаты поиска

Содержание vaddio 999-99800-100

Отзывы: