LEGRAND 0 026 72, Руководство пользователя

Страница: 18 / 29

18/29
Technical data sheet: S000114123EN-1 Updated: Created: 18/01/2021
Cat. No(s): 0 026 72/73/74/76/78/79
KNX controller multi-application DIN
7 . COMMUNICATION OBJECTS (continued)
7 .8 "Blind" parameter (continued)
7 .8 .3 "A/B – Drive Slat" parameter
Determine times for slat
*via duration of slat adjustment (step)
via total duration for slat turning
This parameter defines the slat moving time configuration.
Duration to turn slat from 0% - 100%
in ms [50…60000]
Duration of slat adjustment (step)
in ms [50…1000]
50… *1500 …60000
50… *200 …1000
These parameters define the travelling time of the slat. The time
needed for a complete movement or step movement. Sets the
millisecond of the slat moving time.
Number of slat adjustments
(from 0% = open to 100% = closed)
1… *7 …60
This parameter defines the number of slat steps. The slat steps are
required to turn the slats from fully closed to fully opened.
Limit step commands to
number of slat adjustment
*no
yes
This parameter defines the limit step adjustment command. If it
selected “ no ”, the slat adjustment step count is unlimited.
Position of slat after arriving on lower end
position (100% = disable)
0… *100
The blind will set the slat according to the parameterized value, after
the end position is reached. This parameter is valid for move up down
communication object.
7 .8 .4 "A/B – Functions" parameter
All outputs can be parameterized independent of one other. These
parameters are only visible in blind operation.
• Enable position/presets
• Weather alarm
• Forced position
• Feedbacks
The functions are described independently in detail below.
7 . COMMUNICATION OBJECTS (continued)
7 .8 "Blind" parameter (continued)
7 .8 .4 "A/B – Functions" parameter (continued)
7 .8 .4 .1 "A/B – Position/Presets" parameter
This function allows you set a height position or slat position, directly
using with communication object.
Enable communication objects
“Move to pos . Height/Move slat 0…255”
*no
yes
The communication “ Move to position height 0…255 ” and “ Move
slats 0…255 ” allow you to set the absolute position values. The height
position object is responsible for the height position of blind. The slat
position object is responsible for the slat-opening angle. The limit
position %0 means the blind fully up or slat closed up, %100 means
the blind fully down or slat closed down.
Enable communication objects
“Move to/set position1-4” 1 bit
*no
yes
If the parameter selected “ yes ”, “ Move to position 1, 2 ”, “ Move
to position 3, 4
”, “
Set position 1, 2
”, and “
Set position 3, 4
” 1-bit
telegrams are enabled. The saved or downloaded position can be
easily changed or called with this communication object. The new
position is accepted into the devices memory via “
Set position
”
communication objects.
Overwrite position values during
download
*no
yes
This parameter is selected the reaction of the position set.
• Set the parameter to “
no
”:
During storage of a scene, the position values are stored in the
device. You can protect your custom blind position.
• Set the parameter to “
yes
”:
The original ETS parameter values can be reload into the device
during ETS download operation.
Position 1: Height in % [0…100]
(0% = top; 100% = bottom)
0…
*20
…100
Position 1: Slat in % [0…100]
(0% = top; 100% = bottom)
0…
*20
…100
Position 2: Height in % [0…100]
(0% = top; 100% = bottom)
0…
*40
…100
Position 2: Slat in % [0…100]
(0% = top; 100% = bottom)
0…
*40
…100
Position 3: Height in % [0…100]
(0% = top; 100% = bottom)
0…
*60
…100
Position 3: Slat in % [0…100]
(0% = top; 100% = bottom)
0… *60 …100
Position 4: Height in % [0…100]
(0% = top; 100% = bottom)
0… *80 …100
Position 4: Slat in % [0…100]
(0% = top; 100% = bottom)
0… *80 …100
These parameters define the blind preset height/slat position. Slat
positions are only visible when the blind type is selected “ Venetian
blind
”.
CONTENTS