
It's little cumbersome to always refer to the full name of the
Spirit.ocx
control. A simpler syntax, using
With
, looks like this:
Sub HelloSpiritII ()
With DummySpiritForm.Spirit1
.InitComm
.PlaySystemSound 0
.CloseComm
End With
End Sub
Page 163
Immediate and Delayed Gratification
The functions in
Spirit.ocx
can be
immediate, delayed,
or both. An immediate function executes as soon as you call it. Delayed functions can be placed inside a program and executed later. For
example,
On
is both an immediate and delayed function. You can call it to turn on some outputs immediately, or you can call it to add it to a program that will be executed later.
The following subroutine plays a little song using the
PlayTone
function in its immediate mode:
Sub Charge()
With DummySpiritForm.Spirit1
.InitComm
.PlayTone 392, 10
.PlayTone 523, 10
.PlayTone 659, 10
.PlayTone 784, 20
.PlayTone 659, 10
.PlayTone 784, 20
.CloseComm
End With
End Sub
Instead of executing things on the RCX immediately, you can store them for later. The following subroutine redefines Program 5 on the RCX to play the same song:
Sub ChargeProgram()
With DummySpiritForm.Spirit1
.InitComm
.SelectPrgm 4
.BeginOfTask 0
.PlayTone 392, 10
.PlayTone 523, 10
.PlayTone 659, 10
.PlayTone 784, 20
.PlayTone 659, 10
.PlayTone 784, 20
.EndOfTask
Pause 1
.CloseComm
End With
End Sub
Sub Pause(ByVal duration As Integer)
Start = Timer
Do While Timer < Start + duration
Loop
End Sub
Содержание MINDSTORMS Robots
