P-CLAMP
M4-1.79 X 10
SCREW FOR
PLASTIC
EXTENSION ARM
SCREEN HOLDER
BRACKET
TETHER
#10-32 X 1/2 BHCS
PIN-IN-TORX
M5 FLAT WASHER
#10-32 SQUARE NUT
SCREEN STIFFENER
BRACKET
UNIVERSAL TRAY
(NOT INCLUDED)
USB NIGHT EYE
(NOT INCLUDED)
CLAMP
MAIN SCREEN
SUPPORT
DESCRIPTION
QTY.
#10-32 X 0.375" SQUARE X 0.103" NUT
1
#10-32 PIN-IN-TORX BHCS
1
M5 X 5.3 X 15 X 1.2 THK WASHER
1
M4 - .7 X 8 FHMS
2
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
WEIGHT: (GR)
SCREEN STIFFENER UT.X
04-09-09
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
877-88-LEDCO
www.ledco.net
SS-0032-IS-A
PRODUCT DESCRIPTION
THIS PRODUCT PROVIDES SUPPORT FOR
THE SCREEN ON A COMPUTER WHEN
BEING HELD IN THE UNIVERSAL TRAY
D
C
B
A
A
B
C
D
1
2
3
4
5
6
7
8
8
7
6
5
4
3
2
1
PRODUCT I.D.
DATE
PRODUCT NAME
REV. DATE
DRAWING NUMBER:
SS.UT.X
HARDWARE KIT CONTENTS:
INSTALLATION INSTRUCTIONS:
1. TO INSTALL SCREEN STIFFENER, TURN UNIVERSAL TRAY
BOTTOM SIDE UP WITH THE BACK TOWARDS YOU.
2. PLACE SQUARE NUT IN SLOT OF REAR TRAY.
3. POSITION BRACKET OF SCREEN STIFFENER SO MOUNTING
HOLE LINES UP WITH OPENING IN SQUARE NUT.
4. ALIGN TWO TEETH IN BRACKET WITH SLOTS IN REAR FENCE.
INSTALL 10-32 X 1/2 PIN-IN-TORX SCREW AND M5 FLAT WASHER
THROUGH BRACKET AND INTO NUT. TIGHTEN TO 22 IN LBS 10%
5. PLACE COMPUTER IN TRAY AND CLOSE MECHANISM.
6. EXTEND EXTENSION ARM OUT ALL OF THE WAY TO STOP.
7. EXTEND SCREEN HOLDER TO LIMIT OF TRAVEL WITHOUT IT
COMING OUT OF TRACK.
8. OPEN SCREEN OF COMPUTER TO DESIRED ANGLE. LOOSEN
CLAMP AND BRING SCREEN STIFFENER SUPPORT UP TO BACK OF
SCREEN AND TIGHTEN CLAMP.
9. SLIDE EXTENSION ARM IN SO THAT SCREEN HOLDER TOUCHES
SIDE OF SCREEN.
10. SLIDE SCREEN HOLDER IN SO THAT IT FITS TIGHT AGAINST
SCREEN.
NOTE:
- FINGER IS DESIGNED TO DETACH AND BE HELD BY TETHER WHEN
SCREEN IS CLOSED.
- CLAMP CAN BE TIGHTENED BY LOOSENING LEVER ARM,
ROTATING NUT AND THEN RETIGHTENING LEVER ARM.
-NIGHT EYES (NE.USB-A) CAN BE INSTALLED ONTO BRACKET
USING P-CLAMP AND SCREW PROVIDED IN NIGHT EYES
HARDWARE KIT. PLACE P-CLAMP AROUND NIGHT EYES, ALIGN
WITH HOLE ON BACK OF MAIN SCREEN SUPPORT AND INSTALL
SCREW. TIGHTEN TO 1 N-M 10% OR 8.8 IN-LBS 10%.
WARNING: ALL
LEDCO PRODUCTS ARE DESIGNED WITH SAFETY OF USE AND INSTALLATION IN MIND. HOWEVER, IT
IS THE SOLE RESPONSIBILITY OF THE OWNER/OPERATOR OF A VEHICLE USING
LEDCO MOUNTING AND DOCKING
EQUIPMENT, TO INSURE THAT THE EQUIPMENT IN INSTALLED SO THAT IT WILL NOT INTERFERE WITH VEHICLE
OPERATION, INTERFERE WITH SAFETY DEVICES, OBSTRUCT VIEW OF DRIVING CONDITIONS, OR IN ANY WAY
DEGRADE OCCUPANT SAFETY. IMPROPER INSTALLATION CAN CAUSE SERIOUS INJURY IN THE EVENT OF AN
ACCIDENT. INSTALLATION SHOULD ONLY BE PERFORMED BY QUALIFIED PROFESSIONALS. COMPUTERS AND
MOTION DEVICES MUST BE MOVED TO AND STOWED/SECURED IN THEIR SAFE DRIVING POSITIONS BEFORE
OPERATING VEHICLE.
492
(SHEET 1 OF 2)
