No Spot COB Lighting LED Flex Strip
Model
: HH-SCOBX-528-12 (X = COLOR)
LISTED
use only with
Class 2 Type
power units
12V
DC Power
3.0
WATTS
FOOT
SAFETY & WARNINGS
Disconnect power before installing or servicing (at breaker point).
Use only with LED World’s Class 2 Type power supply.
Indoor use, Dry locations. Do not expose LED Flex Strip to moisture.
This product is intended to be installed and serviced by a qualified licensed electrician. Install in accordance with the National Electric Code, and local regulations. Only power
with a (listed) constant voltage Class 2 power supply (12V DC).
Never plug into 120V AC. The product requires a optional class 2 Transformer (Power Supply).
LED WORLD INC. warranties this product for three year (some exceptions may apply) from the date of shipping unless otherwise noted in writing. This warranty is expressly in lieu of all other warranties expressed or
implied. Under this Limited Warranty, the obligation of the company is limited to replacing on a prorated basis, at its option, any component found to be defective. This Limited Warranty does not apply to damage
caused by buyer or alteration to the product or incorrect power supply. Factory warrantees are covered by the original manufacturer and claims must be submitted to them. This product must be used with LED
World’s class 2 power supply. Failure to do so will void limited warranty.
THREE YEAR LIMITED LIGHTING WARRANTY
LED World Inc. And its providers will never be liable to you or any other person for any indirect, incidental, consequential, special, punitive or exemplary loss or damage arising from, connected with, the purchase
of products, including but not limited to loss of data, business, markets, cost of labour, savings, income, profits, use, production, reputation or goodwill, anticipated or otherwise, or economic loss, under any theory
of liability (whether in contract, tort, strict liability or any other theory or law or equity), regardless of any negligence or other fault or wrongdoing (including without limitation gross negligence and fundamental
breach) by led world inc or any person for whom led world inc is responsible, and even if led world inc has been advised of the possibility of such loss or damage being incurred.
If a product is defective, we will replace the product with similar or identical product or at our option a credit towards a future purchase. To make a claim under this warranty, obtain a return authorization number.
Ÿ
Not for use in mission critical, aircraft, emergency signs or lifesaving equipment.
Ÿ
Only qualified electrician or engineer can perform installation familiar with low voltage wiring techniques. Correct polarity is imperative (+/- is marked on printed circuit). Parallel
connection only.
Ÿ
DO NOT install on flammable material or possibility of in the future. Do not install any luminaire closer than 6 inches (15.25 cm) from any curtain, or similar combustible
materials.
Ÿ
Static electricity can damage LED(s). Handle with care.
Ÿ
Inspect installation after one hour and thereafter regularly.
Ÿ
Voltage must not exceed
12VDC
and must be regulated.
The Voltage is printed at cutmarks.
Check that it is the correct voltage before applying power.
Ÿ
For stationary use only and not subjected to possible pressure or movement (or in the future).
Ÿ
Not for in-wall use.
Ÿ
Max. Soldering temperature cannot exceed 250°C (482°F) for a max of 4 seconds. Use 22~20 AWG wire to connect.
Ÿ
Use correct wiring as required by local electrical code. Use a 20 gauge wire to attach to strip by solder (2464 type of wire). Connection to power source may use Wago™ 222-413
in hardwire applications.
Ÿ
Conductors of extra-low-voltage circuits be rigidly supported.
Ÿ
Cable lighting systems not be installed in bathrooms.
Ÿ
Keep Flex strip spaced ¾” apart if placing next to each other.
Ÿ
The light and all its components cannot be mechanically pressed. Never apply to surface above 40c (104F).
Ÿ
Product is sold in the maximum length.
Do not exceed or extend the length of the roll.
Ÿ
This is not a toy. Keep out of children's reach.
Ÿ
LED Flex Strip is bendable on one flat widest plane. Maximum bend radius is 4 inches (100mm) on one plane (flat).
Ÿ
Do not stare directly into the LED Light. Install LED lighting out of direct sight.
Ÿ
Conductors not be installed in contact with combustible materials and not run through walls, ceilings, floors or partitions, and; Uninsulated conductors not be installed less than
2.2 m (86”) from the floor.
Ÿ
Product has an adhesive tape on back. Adhesion can only be made once and the LED strip must fully adhere to surface (flush). Failure to do this step will damage product. Rigidly
support wires with wire clamps.
Ÿ
During installation, do not damage the printed circuit. Exposed wires can cause short circuit damaging product and creating a serious hazard. Do not mount in a manner or
support LED Strip light in a manner that can damage the outer jacket or cord insulation. Do not install this lighting system where the exposed bare conductors can be shorted or
contact any conductive materials. Carefully check that there is no wire cross-over or possibility in the future in area of installation.
Ÿ
To reduce the risk of fire and overheating, make sure all connections are tight.
Ÿ
Only install on smooth flat surfaces free of burrows that are fire retardant.
Ÿ
Do not power when rolled
. Lighting must be installed in a straight line on a flat surface. Do not curl or twist and roll out completely straight before applying power.
1/4
KG
Never Nail or use Staples
Only power with 12VDC
Class 2 Power Source
Never apply weights or walk on strips
Apply to surface at room temperature. Keep
away from flammable materials. Surface
temperature MAX 40°C (104°F). Don’t install under,
above or near heat sources (i.e. stoves, fireplaces) etc.
IMPORTANT INSTRUCTIONS
Use only with Class 2 Type power supply. Using with any other type of power supply will void the limited warranty.
Please read instructions before using product and
SAVE THESE INSTRUCTIONS.
Before using this product make sure you have right color, product (item
number) and voltage (printed on product). Check for possibility of damage during shipping. If damaged, or wrong product, do not use. Disconnect power before
installing or using.
STATIC ELECTRICITY
CAN DAMAGE
PRODUCT
1-800-387-4081
ledworldlighting.com ledworld.ca
|
Copyright © 2022 LED WORLD INC™. All Rights Reserved. We are not responsible for errors or omissions. Product and specications subject to change without notice. Registered trademarks are owned by their respective registers, or licensee(s).
LED World Inc. | #130 10615 48 ST SE | CALGARY, AB T2C 2B7 | CANADA | Version 1.3 08/22/22
