RVE01440DME
220/240V 50Hz
14W
1050lm
4000K
85
110°
0.7
-20°C ~ 35°C
65
Class II
360 detection angle,
1-8m motion
2.8m mounting height
Adjustable time delay 8
second ~ 12 minutes
Daylight to night adjustable
6V x 1Ah Ni-Cd
Greater than 4 years
normal use
300mm
91mm
1.35kg
3 Years
Model No:
Supply Voltage:
Power Consumption:
Lumen Output:
CCT:
CRI:
Beam Angle:
Power Factor:
Ta Range:
IP Rating:
Safety Class:
Detection range:
Time Delay:
Light Level Adjustment:
Battery
Battery Life
Diameter:
Depth:
Weight:
Warranty:
Suitable for mounting on a normally flammable surface
This fitting is not suitable for installation where ambient air temperature
is above 35°C
Complies with EN60598-1:2008+A11:2009, EN62493:2010,
EN61547:2009, EN61000-3-3:2008, EN60669-1:1999+A2:2008
EN61000-3-2:2006+A1:2009+A2:2009, AS/NZS 2293.3
EN5515:2006+A1:2007+A2:2009,
Optimal mounting height of 2.5m. Turn the dial fully
anticlockwise to select minimum range ( approx. 1m)
and fully clockwise to select maximum range (approx. 8m).
The light can be set to stay ON for any period of time
between approx. 8sec ( turn fully anticlockwise ) and a
maximum of 12min ( turn fully clockwise ). Any movement
detected before this time elapse will re-start the timer. It is
recommended to select the shortest time for adjusting the
detection range and for performing the walk test.
Lux levels can be selected anywhere from 2-2000lux.
Turn the dial fully anticlockwise to select dusk- to-dawn
operation at about 10lux.Turn it fully clockwise to select
daylight operation at about 2000lux. The dial must be
turned fully clockwise when adjusting the detection zone
and performing the walk test in daylight.
The green led should come on indicating correct battery charge status,
all LEDs will come on.When supply to the switched live PL is lost,
battery will operate fitting in emergency mode. Interrupt supply by
pressing the test switch, the fitting will then operate in emergency mode
for a short period of time.
Issue 1 250515
VEGA 14W IP65 BULKHEAD, 4000K, PLAIN DIFFUSER,
MICROWAVE SENSOR, EMERGENCY, GREY & BLACK
RVE01440DME-01, RVE01440DME-04, RVE01440DME-24
Information for the Product user:
1. Please note the requirement to dispose of Waste Electrical & Electronic Equipment separately from household waste (WEEE marked with
crossed out wheelie bin symbol).
2. Please consider your role in contributing to re-use and recycling by returning this product at end of life to a collection centre for waste electrical
equipment or a Civic Amenity site, or to a retail outlet from which you are purchasing a replacement.
3. This equipment may contain substances that are hazardous to health and the environment if disposed of carelessly. It is important that it is
separated from normal household waste and recycled in the WEEE chain
4. The “crossed out wheelie bin symbol” on a product indicates this equipment must not be disposed of in normal household waste, but should be
disposed of according to local WEEE regulations
The Installation must be carried out by an electrician
LED Group
Western Retail Park
Tel: +353 1 7099000
Nangor Road
Fax: +353 1 7099060
Dublin 12
Email: [email protected]
Ireland
Website: www.led.ie
ISO 9001:2008
Q UAL IT Y ASSU RED CO MPANY
1
INSTRUCTION MANUAL
PLEASE READ INSTRUCTION BEFORE COMMENCING INSTALLATION AND RETAIN FOR FUTURE REFERENCES.
! Electrical products can cause death or injury, or damage to property. If in any doubt about the installation or
use of this prodcut, consult a competent electrician
Note:
Product technical information and specification may change over time without prior notification. For the latest
technical information please visit our web site www.ledgrouprobus.com or www.ledgrouprobus.com.au or ideal.co.nz
Specifications
Installation
Sensor symbol
Switch testing
1. Ensure mains supply is switched off before commencing work
2. Ensure there is at least 100mm of free space around the
luminaire location
3. Remove diffuser and LED plate from base of the fitting
4. Drill cable entry and mounting holes in the base
5. Mark appropriate fixing hole positions on wall, check location
of buried cables, pipes and other building services before drilling.
6. Feed supply cables to cable entry hole and attach base to surface
7. Write installation date on battery and connect battery
8. Connect wires from unswitched supply to terminals on
plate, brown to PL and Blue to N; For fitting always on , link terminal
“SL” to terminal “PL”, fitting controlled by switch connect switched live
wire to terminal SL and permanent live to PL.
Note: if “SL” terminal not connected, fitting works as non-maintained
9. Attached LED plate to the base: align the centre point of the
unlock & lock indicator on the tray with the location mark on
the base, rotate clockwise so that it is secure
10. Refit trim/ diffuser to base. ( note: ensure that trim and base
are aligned )
