Lectrosonics DM1612, Справочное руководство, Страница: 37 / 48

37
Reference Manual for Operation
Rio Rancho, NM – USA
outlb (output channel label)
This command may be used as a query to read the
output channel text label, or as an update to set the
label. The output channel is specified by using the
address syntax. Addresses must be in the range 1 to 24.
The data type is string, with a limit of 15 characters.
Examples:
REQUEST RESPONSE
QUERY outlb(1)? OK “Zone 3”
UPDATE outlb(12)=”Gallery” OK
outlv (output level)
This command may be used as a query to read the
output channel level. The output channel is specified by
using the address syntax. Addresses must be in the
range 1 to 24. The data type is integer, in the range -70
to +20, representing the RMS audio level in dBu as
measured AFTER the mixing matrix. If the channel
address is wildcarded, then the data type is an array of
integer of size 24.
Examples:
REQUEST RESPONSE
QUERY outlv(21)? OK -23
QUERY outlv(*)? OK {3,-4,-66,...,-62,-59,-4}
outmic (output mic level)
This command may be used as a query to read the
output mic level status, or as an update to set the status.
The output channel is specified by using the address
syntax. Only select outputs are capable of this action,
addresses must be in the range 9 to 12 or 21 to 24. The
data type is integer, either “1” meaning that the output is
attenuated to mic level (40 dB), or “0” meaning that it is
not.
Examples:
REQUEST RESPONSE
QUERY outmic(9)? OK 1
UPDATE outmic(24)=0 OK
outmt (output mute)
This command may be used as a query to read the
output channel mute status, or as an update to set the
status. The output channel is specified by using the
address syntax. Addresses must be in the range 1 to 24.
The data type is integer, either “1” meaning that the
output is muted, or “0” meaning that it is not. If the
channel address is wildcarded, then the data type is an
array of integer of size 24. In this case the value
99 may
be used in an update to indicate that a particular output
mute is to
remain unchanged by the command.
Examples:
REQUEST RESPONSE
QUERY outmt(19)? OK 1
QUERY outmt(*)? OK {0,0,1,...,0,0,0}
UPDATE outmt(11)=0 OK
UPDATE
outmt(*)={0,1,0,...,0,99,99} OK
outmttog (output mute toggle)
This command may be used as a simple comand to
toggle the output channel mute status. The output
channel is specified by using the address syntax.
Addresses must be in the range 1 to 24.
Examples:
REQUEST RESPONSE
COMMAND outmttog(24) OK
outsrc (output signal source)
This command may be used as a query to read the
output signal source status, or as an update to set the
status. The output channel is specified by using the
address syntax. Addresses must be in the range 1 to 24.
The data type is integer, unless the channel address is
wildcarded, in which case the data type is an array of
integer of size 24. The following values are allowed:
· 0 means normal operation, the output channel is fed
by the mixing matrix
· 1 means that the output channel is fed by a 0 dBu
pink noise source
· 2 means that the output channel is fed by a 0 dBu, 1
kHz tone source
In the case of an update with the channel address
wildcarded, the value
99 may be used to indicate that a
particular output source is to remain unchanged by the
command.
Examples:
REQUEST RESPONSE
QUERY outsrc(9)? OK 0
QUERY outsrc(*)? OK {0,0,1,...,0,0,2}
UPDATE outsrc(24)=2 OK
UPDATE
outsrc(*)={0,0,1,...,99,99,99} OK
Serial Interface & Control Commands (cont'd)