LeCroy USB Protocol Suite Advisor T3 Скачать руководство пользователя страница 365

Страница: 365 / 388

USB Protocol Suite

User Manual

Chapter 13: Updates

LeCroy Corporation

351

13.4 License Information

You can view license information by selecting

Display License Information

from the

Help menu. The License Information window provides a list of the named features
supported by the current software version.

Named features enabled on your PC are indicated by

Yes

in the Purchased column.

Named features that are not enabled on your PC are indicated by

in the Purchased

column. Whether or not named features are enabled depends on the license key stored
in your analyzer.

Содержание USB Protocol Suite Advisor T3





































































































































































































































































































































































































Результаты поиска

Содержание USB Protocol Suite Advisor T3

Отзывы:

Бренды по названию

Популярные бренды

LeCroy USB Protocol Suite Advisor T3, Руководство пользователя

Результаты поиска

Содержание USB Protocol Suite Advisor T3

Отзывы:

Бренды по названию

Популярные бренды