LC Packings Probot 161403 Скачать руководство пользователя страница 32

Страница: 32 / 118

Installation and Getting Started

2-12

D960R3

User’s Manual Probot

2.6

Introduction to the

Carrier

™

Software

The following sections provide a basic introduction in the

Carrier Liquid

Handling Application Designer Software (V2.0) and information of how to setup

and use the software. For more detailed information, refer to the user’s manual

of µCarrier provided with the CD ROM.

2.6.1

Key Features

To improve the ease of use, the following features have been introduced in

Carrier 2.0 and can be found throughout the program.

•

One window design

– All relevant information is displayed in one window.

•

Various wizards

– Easy design of sample carriers, trays and applications.

•

Easy file access

– via the new browser pane.

•

‘What You See Is What You Get’ operation

(WYSIWYG) – in both, the editors

and the wizards.

•

Basic fractionation task

– Only the most important settings need to be

programmed, what can be set by default is set by default.

•

Advanced fractionation task

– Advanced settings can be programmed to

achieve for optimized applications.

New button opens the wizard, corresponding to the active editor

WYSIWYG
Changes made in the settings, are
immediately visible in the Preview window

Easy file access
with preview
option.

Only the most

relevant settings

are displayed.

FIGURE 2-6 Sample Carrier Window

Note:

Carrier 2.0 is backward compatible, e.g. you can load your old

applications in

Carrier 2.0. Saving them again in

Carrier 2.0 will automatically

update your programs.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды