LC Packings Probot 161403 Скачать руководство пользователя страница 20

Страница: 20 / 118

Introduction

1-6

D960R3

User’s Manual Probot

1.7

About this Manual

This manual describes the LC Packings Probot Micro Fraction Collector and

includes the following information:

CHAPTER 2:

Installation and Getting Started

describes how to install the

Probot and the

Carrier Software. It includes the various steps that should be

performed to setup the system, defines how to define a table and targets, set up
a task list with the

Carrier software and prepare the system for operation.

CHAPTER 3:

Maintenance and Troubleshooting

describes a variety of

maintenance procedures to optimize the performance of the Probot Micro

Fraction Collector. In addition, it discusses how the operator can determine the

cause of a difficulty in the operation of the instrument and includes a list of

spare/replacement parts.

CHAPTER 4:

Specifications

presents the specifications of the Probot.

In addition, a number of appendices discussing different topics in more details

are included:

APPENDIX A:

Dosage Module Purge Routine

provides a step-by-step procedure

of how to purge the syringe and tubing of the dosage module properly.

APPENDIX B:

Peak Collection in Conjunction with CHROMELEON® Software

discusses the setup of the CHROMELEON and the

Carrier software packages

and the Probot for peak collection.

APPENDIX C:

Table Alignment Instructions

discusses alignment procedures that

are recommended whenever the instrument has been relocated or shipped.

APPENDIX D:

The Vacuum Waste Removal Option

describes the features and

usage of this option in conjunction with the CHROMELEON software.

APPENDIX E

: Installing and Using the Belkin

™

USB Video Adapter describes the

installation and usage of the Belkin VideoBusII Image Capture Device.

If you are using the Probot Micro Fraction Collector in conjunction with the

LC Packings UltiMate System and/or CHROMELEON software, please refer to the

documentation provided with these products for supplemental information.

The Probot Micro Fraction Collector is used with equipment supplied by other

manufacturers (e.g. a mass spectrometer). The manuals provided with these

systems should be consulted for additional information (e.g. interfacing).

The manual provides basic information about how to install, setup and use the

Carrier software package. In addition, it provides information about defining

tables and targets and how to control the Probot Micro Fraction Collector. For
more detailed information how to use the

Carrier software package refer to the

software manual provided on the

Carrier installation CD ROM.

Note: This manual covers the Probot with S/N 1120 or higher and with the

standard Needle-Tee or the Micro-Tee installed (factory installed since January

2004). If you are using instruments with a serial number lower than 1120, please
refer to the documentation provided with the instrument.

Содержание Probot 161403























































































































Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды

LC Packings Probot 161403, Руководство пользователя

Результаты поиска

Содержание Probot 161403

Отзывы:

Похожие инструкции для Probot 161403

Бренды по названию

Популярные бренды