background image

Filling the Fuel Tank

Fill the fuel tank with fresh unleaded gasoline (Figure 13).

Figure 13

1.

1/4 inch (6 mm)

Important:

Do not use E85 or E20 fuel. Alternative

fuels with high alcohol content can cause hard
starting, poor engine performance, and may cause
internal engine damage.

Checking the Engine Oil Level

Service Interval:

Before each use or daily

1. Move the snowthrower to a level surface.

2. Clean around the oil fill cap (Figure 14).

Figure 14

1.

Oil fill cap

3. Unscrew the oil fill cap and remove it.

4. If the oil level is low, keep the snowthrower in the

operating position and

carefully

pour oil into the

crankcase until the point of overflow. (Max. fill: 21

oz. (0.62 l), type: SAE 30 detergent oil with an API
service classification of SJ, SL, or higher.)

5. Screw the oil fill cap into the oil fill hole and tighten

it securely.

Starting the Engine

1. Turn the ignition key clockwise to the On position

(Figure 15).

Figure 15

2. Pull out the choke lever (Figure 16).

Figure 16

1.

Choke lever

3. Firmly push in the primer 3 times with your thumb,

holding the primer in a for a second before releasing
it each time (Figure 17).

Figure 17

Note:

Remove your glove when you push in the

primer so that air cannot escape from the primer
hole.

9

Содержание Insight 34001





















Отзывы: