background image

Rev. 6/18/97

What Is Covered By This Express Warranty?

LawnĆBoy Inc. promises to repair any LawnĆBoy

snowthrower used for residential purposes if defective

in materials or workmanship for a period of two years

from the date of purchase. Products used for commerĆ

cial, rental or institutional use are warranted for a periĆ

od of 45 days from the date of purchase. The cost of

parts and labor are included. Transportation within a

15 mile radius of the servicing dealer is covered for

twoĆstage snowthrowers. Single stage snowthrowers

are excluded from the transportation coverage proĆ

vided by this warranty.

How Do You Get Warranty Service?

Should you feel your LawnĆBoy product contains a deĆ

fect in materials or workmanship, contact the dealer

who sold you the product or any Authorized LawnĆBoy

Service Dealer. The Yellow Pages of your telephone diĆ

rectory is a good reference source. The dealer will eiĆ

ther arrange service at his/her dealership or recomĆ

mend another Authorized Service Dealer who may be

more convenient. You may need proof of purchase

(copy of registration card, sales receipt, etc.) for warĆ

ranty validation.
If for any reason you are dissatisfied with the Service

Dealer's analysis of the defect in materials or workĆ

manship or if you need a referral to a LawnĆBoy SerĆ

vice Dealer, please feel free to contact us at the followĆ

ing address:

LawnĆBoy Customer Service Department

8111 Lyndale Avenue South

Bloomington, MN 55420-1196

612-888-8801

800-526-6937

What Must You Do To Keep The Warranty

In Effect?

You must maintain your LawnĆBoy Product by followĆ

ing the maintenance procedures described in the opĆ

erator's manual. Such routine maintenance, whether

performed by a dealer or by you, is at your expense.

A TWO YEAR FULL WARRANTY

Snowthrowers

What Does This Warranty Not Cover?

and

How Does Your State Law Relate To This

Warranty?

There is no other express warranty except for special

emission system coverage on some products. This

express warranty does not cover:

D

Cost of regular maintenance service or parts,

such as filters, fuel, lubricants, and tuneĆup

parts.

D

Any product or part which has been altered or

misused or required replacement or repair due

to normal wear, accidents, or lack of proper

maintenance.

D

Repairs necessary due to improper fuel, conĆ

taminants in the fuel system, or failure to proĆ

perly prepare the fuel system prior to any periĆ

od of nonĆuse over three months.

All repairs covered by this warranty must be perĆ

formed by an Authorized LawnĆBoy Service Dealer

using LawnĆBoy approved replacement parts.

LawnĆBoy is not liable for indirect, incidental or

consequential damages relating to a breach of

this warranty, including any cost or expense of

providing substitute equipment or service durĆ

ing reasonable periods of malfunction or non-

use pending completion of repairs under this

warranty. Some states do not allow exclusions

of incidental or consequential damages, so the

above exclusion may not apply to you.
This warranty gives you specific legal rights,

and you may also have other rights which vary

from state to state.

Customers who have purchased LAWNĆBOY products exported from the United States or Canada should contact their

LAWNĆBOY Distributor (Dealer) to obtain guarantee policies for your country, province, or state. If for any reason you

are dissatisfied with your Distributor's service or have difficulty obtaining guarantee information, contact the LAWNĆBOY

importer. If all other remedies fail, you may contact us at LawnĆBoy Inc.

COUNTRIES OTHER THAN THE UNITED STATES OR CANADA

Содержание 522R





















Отзывы: